The tractor is powered by a John Deere iTorque™ power system, a combination of engine features and an exclusive hood design providing superior lugging ability, even cooling, and durability. Key engine features include:
A flywheel alternator provides plenty of capacity to quickly recharge the battery and power electrical equipment, such as lights or a sprayer:
Quality fuel system components enhance performance and convenience:
The 48-in. (122-cm) Accel Deep Deck uses the latest in three-spindle mowing technology to raise performance to a higher level:
The 48-in. (122-cm) Accel Deep Mower Deck is a stamped-steel, deep, flat-top design that delivers excellent cut quality, productivity, cleanliness, durability, and versatility. Optimal performance and dispersion of clippings is provided, even at faster mowing speeds:
Deep mower-deck stamping gives excellent cut quality. It allows the cut and suspended material room to exit the deck without getting recut:
Deep mower-deck stamping gives high productivity, which gets the job done fast. It allows the cut and suspended material room to exit the deck quickly, reducing the amount of re-cutting so more power is available to process incoming grass:
Large discharge opening is both high and wide to handle more material:
The flat-top shape of the deck stamping is optimal for keeping itself and the operator clean:
Cleaning a mower deck, both top and bottom, is one of the most frequent maintenance activities:
A wash port is provided to make cleaning the underside of the mower deck easy.
The 48A Mower Deck has strong spindle pockets, to keep the blades aligned, even after years of tough service:
Mower wheels are heavy duty:
Low-tension belt-drive design reduces the side load on engine lower bearings and mower deck bearings for longer life.
The 48A Mower Deck features a 5/8-in. (16-mm) diameter solid-steel rod side bumper that provides extra strength and protection.
Dual-stage E-coat and powder-paint coatings provide extra protection from rust.
The 48A Mower is designed for maximum versatility, providing the greatest ease in changing from one mower discharge mode to another:
A lever-action or electric one-touch MulchControl attachment for the 48A Mower Deck makes mulching more practical for many mowing situations because it not only does an excellent job of mulching but it also allows the mower to be easily converted for times when it is more desirable to side discharge or collect the lawn material. Advantages of mulching grass clippings include:
MulchControl is an innovative, simple design that is easy to use and maintain:
MulchControl is well-suited to the following mowing situations:
MulchControl puts the operator in control of the clippings. The operator can have all the benefits of mulching with the ability to easily change to side discharging or bagging when needed.
While in the side-discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side-discharge mode is essentially a partial-mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:
An optional 7-bu (247-L) rear bagger material collection system (MCS) is available. It provides an efficient means of collecting grass clippings and leaves:
Larger 14-bu (493-L) and 19-bu (670-L) MCS are available, in addition to the 7-bu (247-L) MCS, for specific X300 and X500 Series Tractor models.
The 54-in. (137-cm) Accel Deep Deck uses the latest in three-spindle mowing technology to raise performance to a higher level:
The 54-in. (137-cm) Accel Deep Mower Deck is a stamped-steel, deep, flat-top design that delivers excellent cut quality, productivity, cleanliness, durability, and versatility. Optimal performance and dispersion of clippings is provided, even at faster mowing speeds:
Deep mower-deck stamping gives excellent cut quality. It allows the cut and suspended material room to exit the deck without getting recut:
Deep mower-deck stamping gives high productivity, which gets the job done fast. It allows the cut and suspended material room to exit the deck quickly, reducing the amount of re-cutting so more power is available to process incoming grass:
Large discharge opening is both high and wide to handle more material:
The flat-top shape of the deck stamping is optimal for keeping itself and the operator clean:
Cleaning a mower deck, both top and bottom, is one of the most frequent maintenance activities:
A wash port is provided to make cleaning the underside of the mower deck easy.
MulchControl is an innovative, simple design that is easy to use and maintain:
The 54A Mower Deck has strong spindle pockets, to keep the blades aligned, even after years of tough service:
Mower wheels are heavy duty:
Low-tension belt-drive design reduces the side load on engine lower bearings and mower deck bearings for longer life.
The 54A Mower Deck features a 5/8-in. (16-mm) diameter solid-steel rod side bumper that provides extra strength and protection.
Dual-stage E-coat and powder-paint coatings provide extra protection from rust.
The 54A Mower is designed for maximum versatility, providing the greatest ease in changing from one mower discharge mode to another:
A MulchControl attachment for the 54A Mower Deck makes mulching more practical for many mowing situations because it not only does an excellent job of mulching but it also allows the mower to be easily converted for times when it is more desirable to side discharge or collect the lawn material. Advantages of mulching grass clippings include:
An optional 7-bu (247-L) rear bagger material collection system (MCS) is available. It provides an efficient means of collecting grass clippings and leaves:
Larger 14-bu (493-L) and 19-bu (670-L) MCS are available, in addition to the 7-bu (247-L) MCS, for specific X300 and X500 Series Tractor models.
MulchControl is well-suited to the following mowing situations:
MulchControl puts the operator in control of the clippings. The operator can have all the benefits of mulching with the ability to easily change to side discharging or bagging when needed.
While in the side-discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side-discharge mode is essentially a partial-mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:
An exclusive 4-year or 500-hour (whichever comes first), single-source, bumper-to-bumper warranty* is standard for all John Deere X500 Series Tractors.
*Term limited to years or hours used, whichever comes first, and varies by model. See the LIMITED WARRANTY FOR NEW JOHN DEERE TURF AND UTILITY EQUIPMENT at JohnDeere.com or JohnDeere.ca/TUWarranty for details.
NOTE: In the schematic above, the solid line refers to a four-wheel steer tractor, and the hashed line refers to a two-wheel steer tractor.
Four-wheel steering provides very significant maneuverability and trimming advantages over two-wheel-steering equipped tractors (the following numbers correspond to the schematic above):
1. The uncut circle diameter is greatly reduced, eliminating or greatly reducing the need to back up when trimming around trees, shrubs, etc.
2. Interference from the mower and tractor wheels is eliminated because they are several inches away from the object being trimmed around.
3. The outside turning circle is reduced, reducing the time spent turning and increasing mowing efficiency.
Hydraulic power steering is standard equipment to maximize the benefits of four-wheel steering with both tight turns and easy steering:
The four-wheel steering system is designed for tight turns, leading to greater mowing efficiency:
The integrated hydrostatic transaxle (IHT) encloses the hydrostatic pump and motor rotating groups in the same housing with the differential and axle housing:
When combined with the foot controls, the hydrostatic transmission functions similarly to that of an automatic transmission in an automobile, so the term automatic is often used to describe it.
Key features of the drive system are as follows:
Cruise control is standard equipment:
Traction assist is standard equipment:
Lever-action or electric one-touch MulchControl attachment is available for Accel Deep™ 42-in. (107-cm) (42A), 48-in. (122-cm) (48A), and 54-in. (137-cm) (54A) Mower Decks used on X300 and X500 Select Series™ Tractors.
MulchControl enhances versatility and productivity. A mower deck equipped with MulchControl not only does an excellent job of mowing and mulching, but it can also be quickly converted from side discharging to mulching or vice versa:
Electric MulchControl has the additional advantage of being controlled from the tractor seat by a switch on the dash to operate an electric actuator that moves the baffle to close off the discharge area of the mower deck.
A mower equipped with a MulchControl attachment delivers unprecedented levels of productivity and versatility. The operator has the ability to quickly change between side discharging and mulching. A heavy-duty baffle opens and closes to convert the mower from side discharge mode to mulch mode or vice versa.
MulchControl is an innovative, simple design that is easy to use and maintain:
MulchControl is well-suited to the following mowing situations:
MulchControl puts the operator in control of the clippings. The operator can have all the benefits of mulching with the ability to easily change to side discharging when desired.
Advantages of MulchControl include:
While in the side discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side discharge mode is essentially a partial mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:
Each MulchControl attachment includes everything needed: baffles and mulch blades for all attachments, and the actuator, wiring, and switches for the electric one-touch attachments.
Attachment number | Description | Applications |
BM24794 | 42A MulchControl (lever action) | X300 Series Tractors, Z300 Series ZTrak™ Mowers |
BM24993 | 48A MulchControl (lever action) | X300 and X500 Series Tractors, Z300 and Z500 Series ZTrak Mowers |
BM24994 | 54A MulchControl (lever action) | X300 and X500 Series Tractors, Z300 and Z500 Series ZTrak Mowers |
Attachment number | Description | Applications |
BUC10164 | 42A electric one-touch MulchControl | X300 Series Tractors* |
BUC10165 | 48A electric one-touch MulchControl | X300 and X500 Series Tractors* |
BUC10166 | 54A electric one-touch MulchControl | X300 and X500 Series Tractors* |
* NOTE: Model year 2016-2017 X300 and X500 Series Tractors (X300 serial number 10,001-50,000 and X500 serial number 110,001-130,000) require replacing the tractor wiring harness and dash panel to use an electric MulchControl attachment.
An advantage of lawn tractors is their ability to use attachments for snow removal and other yard-care chores. Lawn tractor owners can add a John Deere snow blower or front blade to make quick work of moving snow whenever the need arises. Weather enclosure and tire-chain attachments add comfort and performance.
Equipment available for snow removal includes:
Rotary tillers are real time savers for preparing seedbeds, controlling weeds, and other tillage jobs.
Equipment available for tilling includes:
The contoured dash has clean, attractive styling and ergonomic controls for easy use:
Instrument display has the look and feel of a modern automobile. A power-up sequence cycles lights and gauges to indicate they are working:
Twin Touch foot pedals control the speed and direction of travel:
Cruise control is standard equipment:
A lift-assist spring is provided on the tractor to minimize lift effort:
A rotary dial knob makes adjusting the mower cut height quick and easy:
Storage for the onboard deck-leveling gauge and the Exact Adjust tool is provided in the storage tray under the tractor’s seat:
Deck-leveling gauge is placed at the appropriate location under the left rear, right rear, and front of the mower deck as the cut height is adjusted using the Exact Adjust tool and front draft arm adjusting nuts.
Pushing with the foot to raise the mower or implement is less strenuous for many operators:
Convenient hydraulic lift lever makes raising and lowering the mower or implement easy:
Depressing the brake pedal applies force to internal wet-disk brake (which provides excellent durability and long life) for safe stopping.
Parking brake control is conveniently located for easy access; holds brake pedal securely in locked position.
The heavy-duty electric PTO clutch is operated with a convenient dash-mounted switch.
The PTO clutch is designed to operate through many on/off cycles.
CAUTION: Children or bystanders may be injured by rotating blades. Before traveling forward or rearward:
NOTE: Operating the mower while backing up is strongly discouraged. RIO should be used only when operating another attachment or when the operator deems it necessary to reposition the machine with the mower engaged.
The frame is made of heavy-duty formed and welded steel, reinforced in critical areas for even greater strength:
The front bumper holds up to four 42-lb (19-kg) Quik-Tatch weights.
The front axle is made of nodular cast iron:
Replaceable bushings are used at the center axle pivot and steering spindles:
The front steering spindles are strong for long life:
A heavy-duty equipment mounting system is used:
Smooth, rounded contours present a modern, styled appearance:
Premium features ensure the versatility of X500 Series Tractors:
Headlights are standard equipment.
High-quality headlights make evening work easier and safer:
The operator station is designed for operator comfort and convenience in operating all controls. The controls are easy to use and color coded for quick identification.
The 15-in. (38-cm) open-back seat (X570, X580) features distinctive styling and is designed for comfort:
The 21-in. (53-cm) high-back seat (X584, X590) provides additional comfort and support for the operator.
The seat suspension is easily adjusted to make most any operator comfortable:
The optional 21-in. (53.3-cm) professional two-piece seat, four-bar suspension, and slide shipped on Signature Series X700 Tractors is available as an upgrade seat and suspension for all X500 Multi-Terrain Tractors (model year 2006-). Key selling features for this seat include:
Armrests increase operator support and comfort, thus reducing fatigue and improving productivity, especially when mowing for extended periods of time. Armrests are adjustable to suit the operator. This armrest attachment is designed for the optional 21-in. (53.3-cm) professional two-piece seat.
A 12-V outlet is standard equipment and provides a convenient plug-in for electrical equipment.
Rubber foot pads make the operator more comfortable:
A cup holder and covered toolbox are conveniently located on the fender next to the operator's seat.
Handles on each fender are useful when getting on and off the tractor.
A mid-vehicle 12-V fast connector, located under the tractor’s fuse box, is included as standard equipment to reduce initial installation time for some attachments that operate on 12-V power from the tractor:
The one-piece hood opens easily to permit checking and servicing the engine:
The engine fuel and oil filters, the oil check/fill tube, and the oil drain tube are exposed for serviceability when the hood is opened.
A mower deck must be level side-to-side and properly adjusted front-to-rear to give the best cutting performance. A removable onboard deck-leveling gauge and a hex-key tool are provided to make adjustment easy. They are securely stored under the tractor seat.
Exact Adjust leveling ports are provided on each side of the operator platform above the mower-level adjusting bolts. With the hex-shaped tool, they provide convenient access to allow quick and easy adjustment of the mower for the best-cut quality of cut.
The Exact Adjust feature is standard on all Select Series™ X300 and X500 Tractors:
Consult the operator's manual for the correct adjusting procedures for each tractor model. Basic adjusting steps to properly level the mower deck include:
NOTE: The adjusting tool supplied with the tractor is an 8-mm ball-hex key, part number M162737. The rounded end allows for some misalignment with the bolt as the deck is adjusted.
Keep a John Deere riding lawn mower running its best and know how it mows with the John Deere MowerPlus app. Simply scan the lawn tractor’s barcode to get custom information. The app helps determine the best time to mow, communicates expert pre-mow tips, offers maintenance reminders, and provides walk-through guides.
Look for the MowerPlus app on the mobile device’s app store.
The app supports residential lawn equipment such as 100 Series, S240, X300, X500, X700, Z200 through Z600, and many similarly-sized older products. It does not presently support tractor models numbered 1000 and larger, such as 1025R.
NOTE: Some product image variation may exist.
Also available is the John Deere MowerPlus smart connector (sold separately).
The John Deere MowerPlus smart connector wirelessly links a Select Series™ X300 or X500 Tractor to the MowerPlus app on a mobile device. The smart connector transmits engine usage to the app, making it easy to track maintenance intervals. It also transmits the fuel level to the app—when thinking ahead about Saturday morning mowing, the operator can make sure the tractor is fueled and ready to go.
Key Specs | x584-lawn-tractor-48-in Current Model |
---|---|
Engine power | 24 hp 17.9 kW |
Engine manufacturer/model | FS730V |
Transaxle type | K72 hydrostatic integrated with transaxle |
Transaxle control | Twin Touch™ pedals |
Rear tires | 24x9.5-12 turf |
Steering type | Power, hydraulic |
Lift system type | Hydraulic |
Cutting width | Accel Deep™ mower deck, 48, 54 in. 122, 137 cm |
U.S. warranty | 4 year/500 hour bumper-to-bumper** (**Term limited to years or hours used, whichever comes first, and varies by model. See the LIMITED WARRANTY FOR NEW JOHN DEERE TURF AND UTILITY EQUIPMENT at JohnDeere.com or JohnDeere.ca/TUWarranty for details.) |
Engine | |
Power | 24 hp 17.9 kW |
Displacement | 44.3 cu in. 726 cc |
Manufacturer/model | FS730V |
Type | Overhead valve, full-pressure lube, oil filter |
Cylinders | V-twin, cast-iron liners |
Governor | Mechanical |
Choke/speed control | Separate levers, automatic choke return |
Cooling method | Air |
Air cleaner | Dry, replaceable with foam precleaner |
Oil drain | No tools |
Fuel system | |
Type | Gasoline |
Fuel delivery | Pulse pump and carburetor |
Fuel gauge | Gauge on dash |
Fuel tank location | Rear |
Fuel fill opening | On left fender, 3 in. 7.6 cm |
Fuel tank capacity | 4.4 U.S. gal. 16.7 L |
Electrical system | |
Battery | 12 V 500 CCA |
Charging system | Flywheel alternator, regulated, 15 amp |
Engine starter | |
Hourmeter | Yes |
Headlights | Two standard, incandescent, 27 W |
Taillights or reflector | Reflectors |
Backup lights | No |
Rear work lights | No |
12-V outlet | Yes |
Transaxle | |
Type | K72 hydrostatic integrated with transaxle |
Control | Twin Touch™ pedals |
Cruise control | Yes, button on dash |
Oil cooler | Fins and fan on transaxle |
Oil filter | Yes, replaceable |
Differential lock | Standard |
Forward speed | 0-7.2 mph 0-11.6 km/h |
Reverse speed | 0-5.2 mph 0-8.4 km/h |
Brakes | Internal wet disc |
Chassis | |
Frame | Welded heavy-duty |
Primer/paint | E-coat/powder |
Weight bracket | Standard front and optional rear - each holds up to four Quik-Tatch weights, 42 lb 19 kg |
Receiver hitch | No |
Front axle | Cast iron front axle, front wheel ball bearings |
Spindle bushings | Metal, replaceable |
Front tires | 16x6.5-8 turf |
Rear tires | 24x9.5-12 turf |
Hood material | Molded-in color hood material reduces sound, will not rust or dent |
Fender deck material | Stamped steel |
Floor mats | Sure-grip rubber |
Storage | Yes, under seat and covered toolbox |
Service interval decal | Yes |
Fender handles/grips | Handles |
Cup holder | Yes |
Equipment mounting | Yes, heavy duty |
Steering | |
Type | Power, hydraulic |
Four-wheel steer | Yes |
Steering wheel | 14 in. 35.6 cm |
Tilt steering wheel | Standard, five position |
Turning radius | 19 in. 48.3 cm |
Uncut circle radius | 48A, 15 in. 38 cm 54A, 12 in. 30 cm |
Seat | |
Type | High-back |
Seat back height | 21 in. 53.3 cm |
Armrests | Optional |
Fore-aft adjustment | While seated, slide rail, 14-position, 7 in. 17.8 cm |
Seat suspension | Tilt, two coil springs, three-position no-tools adjustment for operator weight |
Lift system | |
Type | Hydraulic |
Hydraulic outlets | No |
Mower cut height | 13 positions, 1-4 in. 2.5-10.2 cm |
Cut height increments | 0.25 in. 0.64 cm |
Preset cut height | Yes |
Mower deck | |
Type | Side discharge |
Cutting width | Accel Deep™ mower deck, 48, 54 in. 122, 137 cm |
Construction | Stamped steel deck shell |
Mower deck material | 10 gauge 0.135 in. 3.4 mm |
Mower wash port | Yes |
Mower drive system | Electric power take-off (PTO) clutch, in-line belt |
Mower wheels | Four |
Mower wheel adjustment | Seven-position, spring-loaded pin |
Mower level adjustment | Exact Adjust ports and onboard deck-leveling gauge |
Mower attachability | |
Type | Roll under tractor |
Front draft arms | Attached with spring pins at two points |
Rear draft arms | Quick-pull pins |
Mower wheels rotate | Yes, 90 degrees for easy mower removal |
Drive system | Dual belt |
Safety | |
Meets ANSI standard | Yes |
Meets OPEI standard | Yes |
Backup protection | Reverse Implement Option (RIO) |
Safety video | Yes |
Buyer's notes | |
Notes | Heavy-duty garden tractor transaxle Convenient power steering and hydraulic lift Standard four-wheel steering for exceptional maneuverability and trimming Built-in front weight bracket |
Warranty | 4 year/500 hour bumper-to-bumper** (**Term limited to years or hours used, whichever comes first, and varies by model. See the LIMITED WARRANTY FOR NEW JOHN DEERE TURF AND UTILITY EQUIPMENT at JohnDeere.com or JohnDeere.ca/TUWarranty for details.) |
Optional equipment | |
Mowers | 48A option, 54A option |
Rear bagger | 7, 14, 19 bu 247, 493, 670 L |
Powered material collection | Power Flow™ blower |
Mulching system | Yes, MulchControl™ |
Front thatcher | 38, 46, 54 in. 96.5, 116.8, 137.2 cm |
Front blade | 48 in. 121.9 cm |
Mid-mount blade | |
Snow blower | Two-stage, 47 in. 119.4 cm |
Rotary broom | |
Rotary tiller | |
Sleeve hitch | Yes, implements include box scraper, rear blade, plow, disk, and cultivator |
3-point hitch | |
Rear power take-off (PTO) | |
Plow, moldboard | Yes |
Box scraper | Yes |
Cultivator | Yes |
Rear blade | Yes |
Disk harrow | |
Landscape rake | |
Sprayer | Tow-behind, 15, 25, 45 U.S. gal. 56.8, 94.6, 170.3 L Mounted, 25 U.S. gal. 94.6 L |
Spreader | 125, 175 lb 57.7, 79.4 kg Mounted, 125 lb 57.7 kg |
Front bumper | Standard front bumper/weight bracket |
Brush guard | Yes |
Weather protection | Weather enclosure |
Sun canopy | Yes |
Rear receiver hitch | |
Bucket holder | Yes, double bucket |
Grass striping | Lawn striping kit |
Tractor shovel | 40 in. 101.6 cm |
Front loader | |
Other equipment | |
Tow-behind tools | 19 |
Dimensions | |
Height | 52.25 in. 132.7 cm |
Overall length | 79 in. 201 cm |
Wheelbase | 51.2 in. 130 cm |
Width with mower | 48A, 62.5 in. 159 cm 54A, 68.4 in. 174 cm |
Width with mower (deflector raised for storage) | 48A, 53.6 in. 136 cm 54A, 59.4 in. 151 cm |
Width without mower | 45 in. 114.3 cm |
Weight | 48A Mower, no fuel, 837 lb 380 kg 54A Mower, no fuel, 845 lb 383 kg |
Every owner of a John riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials including firewood, lawn debris, sand, dirt, mulch, garden tools, plants, and bushes.
Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.
NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak™ or ZTrak™ mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck.
Wheels are mounted on a solid, one-piece axle for durability.
Iron and Oilite® wheel bearings with grease fittings provide lubrication for long life.
The pneumatic tires offer the following:
A sloped tailgate design makes emptying the box easier; there is no tailgate to loosen or remove.
A large-diameter hitch pin provides plenty of strength:
An easy-to-use, spring-loaded dump latch allows tilting the box for easier unloading. A steep dump angle makes emptying the cart easier.
Comparison with similar models
Model | Order through | Box capacity (heaped) | Material thickness | Maximum weight | Vehicle compatibility |
7P | Order Zone | 7 cu ft (0.20 m3) | High-density polyethylene (HDPE)** | 450 lb* (204 kg) | EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series |
8Y | Order Zone | 8 cu ft (0.22 m3) | HDPE** | 300 lb* (136 kg) (tow) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
10P | Order Zone | 10 cu ft (0.28 m3) | Polypropylene | 650 lb* (295 kg) | EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series |
13 | Order Zone | 13 cu ft (0.37 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
16YS | Order Zone | 17 cu ft (0.48 m3) | Polypropylene | 800 lb (363 kg), 350 lb (158 kg) when using swivel feature to dump | 100 Series, S240, X300 Series, X500 Series, X700 Series |
17P | Order Zone | 17 cu ft (0.48 m3) | Polypropylene | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
18 | Order Zone | 18 cu ft (0.51 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
21 | Order Zone | 21 cu ft (0.59 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | X700 Series |
*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).
**HDPE is compression molded for optimum thickness in all areas and maximum durability.
7P | 8Y | 10P | 13 | 16YS | 17P | 18 | 21 | |
Box capacity | ||||||||
Heaped | 7 cu ft (0.20 m3) | 8 cu ft (0.22 m3) | 10 cu ft (0.28 m3) | 13 cu ft (0.37 m3) | 17 cu ft (0.48 m3) | 17 cu ft (0.48 m3) | 18 cu ft (0.51 m3) | 21 cu ft (0.59 m3) |
Struck | 5.6 cu ft (0.16 m3) | 6.6 cu ft (0.19 m3) | 8.3 cu ft (0.24 m3) | 10 cu ft (0.28 m3) | 15 cu ft (0.42 m3) | 14 cu ft (0.40 m3) | 15 cu ft (0.42 m3) | 15 cu ft (0.42 m3) |
Maximum weight | 450 lb* (204 kg) | 300 lb* (136 kg) | 650 lb* (295 kg) | 1,000 lb* (454 kg) | 800 lb* (363 kg), 350 lb (158 kg) when using swivel feature to dump | 1,000 lb* (454 kg) | 1,000 lb* (454 kg) | 1,000 lb* (454 kg) |
Box dimensions | ||||||||
Width | 33 in. (84 cm) | 33.68 in. (85.5 cm) | 30.3 in. (77 cm) | 30.25 in. (76.8 cm) | 39.5 in. (100.3 cm) | 39.5 in. (100.3 cm) | 38 in. (96.5 cm) | 48 in. (122 cm) |
Length | 45 in. (114 cm) | 45 in. (114 cm) | 44.5 in. (113 cm) | 48 in. (122 cm) | 58.5 in. (148.6 cm) | 58.5 in. (148.6 cm) | 48 in. (122 cm) | 48 in. (122 cm) |
Depth | 10.5 in. (27 cm) | 10.75 in. (27.3cm) | 12 in. (30.5 cm) | 12 in. (30.5 cm) | 15.5 in. (39.4 cm) | 15.5 in. (39.4 cm) | 18 in. (45.7 cm) | 11 in. (27.9 cm) |
Box construction | Molded | Molded | Molded | Welded | Molded | Molded | Welded | Bolted |
Material | High-density polyethylene (HDPE)** | HDPE** w/UV inhibitor | Polypropylene | 16-gauge, 0.06-in. (1.5-mm) steel | Polypropylene | Polypropylene | 16-gauge, 0.06-in. (1.5-mm) steel | 16-gauge, 0.06-in. (1.5-mm) steel |
Tailgate | None, sloped | None, sloped | None, sloped | Hinged | None, sloped | None, sloped | Hinged | Lift-out/swing-out |
Pneumatic tires | 2 ply | --- | 2 ply | 2 ply | 4 ply | 4 ply | 4 ply | 2 ply |
Size | 13x4-6 | 13x4-6 | 15x6.00-6 | 15x6.00-6 | 16x6.50-8 | 16x6.50-8 | 16x6.50-8 | 20x10.00-8 |
Tread design | Turf | Knobby | Turf | Turf | Turf | Turf | Turf | Turf |
Recommended inflation pressure | 30 psi (207 kPa) | 30 psi (207 kPa) | 14 psi (97 kPa) | 14 psi (97 kPa) | 35 psi (241 kPa) | 28 psi (193 kPa) | 28 psi (193 kPa) | 10 psi (70 kPa) |
Wheel bearings | Iron/Oilite | None | Iron/Oilite | Iron/Oilite | Iron/Oilite | Iron/Oilite | Iron/Oilite | Ball bearings, double sealed |
Grease fittings on wheels | Yes | None | Yes | Yes | Yes | Yes | Yes | None |
Axle diameter | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 1 in. (2.54 cm) | 1 in. (2.54 cm) |
Ground clearance | 5.62 in. (14.3 cm) | 5.25 in. (13.3 cm) | 6.5 in. (16.5 cm) | 6.5 in. (16.5 cm) | 14.25 in. (36.2 cm) | 14.25 in. (36.2 cm) | 7 in. (17.8 cm) | 8.25 in. (21 cm) |
Width, overall | 34 in. (86.4 cm) | 33.68 in. (85.5 cm) | 38 in. (96.5 cm) | 38 in. (96.5 cm) | 39.5 in. (100.3 cm) | 39.5 in. (100.3 cm) | 38 in. (96.5 cm) | 48 in. (122 cm) |
Hitch pin | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip |
Dump angles | 55 degrees | 55 degrees | 56 degrees | 31 degrees | 46 degrees | 46 degrees | 35/40 degrees | 35/40 degrees |
Maximum tongue weight | 100 lb (45.4 kg) | 100 lb (45.4 kg) | 70 lb (31.75 kg) | 100 lb (45.4 kg) | 50 lb (22 kg) | 100 lb (45.4 kg) | 100 lb (45.4 kg) | 100 lb (45.4 kg) |
Shipping weight with carton | 68 lb (31 kg) | 65 lb (29.5 kg) | 79 lb (35.8 kg) | 110 lb (49.9 kg) | --- | 105 lb (47.6 kg) | 170 lb (77.1 kg) | 240 lb (109 kg) |
Net weight | 65 lb (29 kg) | 55 lb (25 kg) | 72 lb (32.7 kg) | 105 lb (47.6 kg) | 103 lb (47 kg) | 105 lb (47.6 kg) | 150 lb (68 kg) | 220 lb (99.8 kg) |
*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).
**HDPE is compression molded for optimum thickness in all areas and maximum durability.
Utility Carts
Chart below shows vehicle compatibility.
An X indicates cart can be used with the pulling unit.
NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.
7P | 8Y | 10P | 13 | 16YS | 17P | 18 | 21 | |
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z335M, Z345M, Z345R, Z355R, Z375R, Z525E, Z535M, Z540M, Z535R, Z540R, Z720E, Z735E, Z730M, Z735M, Z740R | X | X | ||||||
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180 | X | X | X | X | X | X | X | |
S240 | X | X | X | X | X | X | X | |
LT150, LT160, LT180, LT190, LTR180 | X | X | X | X | X | |||
LX280, LX280AWS, LX289 | X | X | X | X | X | |||
X300, X300R, X304, X310, X320, X324, X340, X360, X330, X350, X350R, X354, X370, X380, X384, X390, X394 | X | X | X | X | X | X | X | |
SST15, SST16, SST18 | X | X | X | |||||
G110 | X | X | X | X | X | X | ||
GT235, GT245 | X | X | X | X | X | X | ||
GX255, GX335, GX345, GX355 | X | X | X | X | X | X | ||
X500, X520, X530, X534, X540 X570, X580, X584, X590 | X | X | X | X | X | X | X | |
X465, X475, X485, X495, X575, X585, X595 | X | X | X | X | X | X | X | X |
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758 | X | X | X | X | X | X | X | X |
For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:
Tractor | Additional weight |
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180 | Two 30-lb (14-kg) wheel weights, front Two 42-lb (19-kg) suitcase weights, rear |
S240 | Two 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear |
LT150, LT160, LT180, LT190, LTR180 | Two 34-lb (15-kg) wheel weights, front Two 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190) |
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394 | Two 34-lb (15-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, rear |
SST15, SST16, SST18 | One 88-lb (40-kg) weight kit, front Three 40-lb (18-kg) weights, rear |
G100 | Two 50-lb (23-kg) wheel weights, rear Two 42-lb (19-kg) suitcase weights, rear |
G110 | Two 50-lb (23-kg) plastic shell rear wheel weights |
GT235, GT245 | Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear |
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590 | Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) wheel plastic shell weights, rear |
X465, X475, X485, X495, X575, X585, X595 | Four 42-lb (19-kg) suitcase weights, front Two 70-lb (32-kg) wheel cast-iron starter weights, rear Four 50-lb (23-kg) cast-iron wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear Six 42-lb (19-kg) suitcase weights, rear |
Please contact a local John Deere dealer for availability and pricing information.
7P Poly Utility Cart
Order number: LP21935
Oilite is a trademark of Beemer Precision, Incorporated.
The 8-cu-ft (0.23-m3), 300-lb (136-kg) capacity 8Y Convertible Poly Utility Cart can be used to haul a variety of materials including lawn debris, sand, dirt, mulch, and plants. The unique convertible hitch allows changing the cart from tow-behind mode to push mode without tools.
Key features include:
Every owner of a John Deere riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials including firewood, lawn debris, sand, dirt, mulch, garden tools, plants, and bushes. Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.
NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. See the appropriate vehicle pages for the weight of the vehicle and the mower deck.
Comparison with similar models
Model | Order through | Box capacity (heaped) | Material thickness | Maximum weight | Vehicle compatibility |
7P | Order Zone | 7 cu ft (0.20 m3) | High-density polyethylene (HDPE)** | 450 lb* (204 kg) | EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series |
8Y | Order Zone | 8 cu ft (0.22 m3) | HDPE** | 300 lb* (136 kg) (tow) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
10P | Order Zone | 10 cu ft (0.28 m3) | Polypropylene | 650 lb* (295 kg) | EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series |
13 | Order Zone | 13 cu ft (0.37 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
16YS | Order Zone | 17 cu ft (0.48 m3) | Polypropylene | 800 lb (363 kg), 350 lb (158 kg) when using swivel feature to dump | 100 Series, S240, X300 Series, X500 Series, X700 Series |
17P | Order Zone | 17 cu ft (0.48 m3) | Polypropylene | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
18 | Order Zone | 18 cu ft (0.51 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
21 | Order Zone | 21 cu ft (0.59 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | X700 Series |
*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).
**HDPE is compression molded for optimum thickness in all areas and maximum durability.
7P | 8Y | 10P | 13 | 16YS | 17P | 18 | 21 | |
Box capacity | ||||||||
Heaped | 7 cu ft (0.20 m3) | 8 cu ft (0.22 m3) | 10 cu ft (0.28 m3) | 13 cu ft (0.37 m3) | 17 cu ft (0.48 m3) | 17 cu ft (0.48 m3) | 18 cu ft (0.51 m3) | 21 cu ft (0.59 m3) |
Struck | 5.6 cu ft (0.16 m3) | 6.6 cu ft (0.19 m3) | 8.3 cu ft (0.24 m3) | 10 cu ft (0.28 m3) | 15 cu ft (0.42 m3) | 14 cu ft (0.40 m3) | 15 cu ft (0.42 m3) | 15 cu ft (0.42 m3) |
Maximum weight | 450 lb* (204 kg) | 300 lb* (136 kg) | 650 lb* (295 kg) | 1,000 lb* (454 kg) | 800 lb* (363 kg), 350 lb (158 kg) when using swivel feature to dump | 1,000 lb* (454 kg) | 1,000 lb* (454 kg) | 1,000 lb* (454 kg) |
Box dimensions | ||||||||
Width | 33 in. (84 cm) | 33.68 in. (85.5 cm) | 30.3 in. (77 cm) | 30.25 in. (76.8 cm) | 39.5 in. (100.3 cm) | 39.5 in. (100.3 cm) | 38 in. (96.5 cm) | 48 in. (122 cm) |
Length | 45 in. (114 cm) | 45 in. (114 cm) | 44.5 in. (113 cm) | 48 in. (122 cm) | 58.5 in. (148.6 cm) | 58.5 in. (148.6 cm) | 48 in. (122 cm) | 48 in. (122 cm) |
Depth | 10.5 in. (27 cm) | 10.75 in. (27.3cm) | 12 in. (30.5 cm) | 12 in. (30.5 cm) | 15.5 in. (39.4 cm) | 15.5 in. (39.4 cm) | 18 in. (45.7 cm) | 11 in. (27.9 cm) |
Box construction | Molded | Molded | Molded | Welded | Molded | Molded | Welded | Bolted |
Material | High-density polyethylene (HDPE)** | HDPE** w/UV inhibitor | Polypropylene | 16-gauge, 0.06-in. (1.5-mm) steel | Polypropylene | Polypropylene | 16-gauge, 0.06-in. (1.5-mm) steel | 16-gauge, 0.06-in. (1.5-mm) steel |
Tailgate | None, sloped | None, sloped | None, sloped | Hinged | None, sloped | None, sloped | Hinged | Lift-out/swing-out |
Pneumatic tires | 2 ply | --- | 2 ply | 2 ply | 4 ply | 4 ply | 4 ply | 2 ply |
Size | 13x4-6 | 13x4-6 | 15x6.00-6 | 15x6.00-6 | 16x6.50-8 | 16x6.50-8 | 16x6.50-8 | 20x10.00-8 |
Tread design | Turf | Knobby | Turf | Turf | Turf | Turf | Turf | Turf |
Recommended inflation pressure | 30 psi (207 kPa) | 30 psi (207 kPa) | 14 psi (97 kPa) | 14 psi (97 kPa) | 35 psi (241 kPa) | 28 psi (193 kPa) | 28 psi (193 kPa) | 10 psi (70 kPa) |
Wheel bearings | Iron/Oilite | None | Iron/Oilite | Iron/Oilite | Iron/Oilite | Iron/Oilite | Iron/Oilite | Ball bearings, double sealed |
Grease fittings on wheels | Yes | None | Yes | Yes | Yes | Yes | Yes | None |
Axle diameter | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 1 in. (2.54 cm) | 1 in. (2.54 cm) |
Ground clearance | 5.62 in. (14.3 cm) | 5.25 in. (13.3 cm) | 6.5 in. (16.5 cm) | 6.5 in. (16.5 cm) | 14.25 in. (36.2 cm) | 14.25 in. (36.2 cm) | 7 in. (17.8 cm) | 8.25 in. (21 cm) |
Width, overall | 34 in. (86.4 cm) | 33.68 in. (85.5 cm) | 38 in. (96.5 cm) | 38 in. (96.5 cm) | 39.5 in. (100.3 cm) | 39.5 in. (100.3 cm) | 38 in. (96.5 cm) | 48 in. (122 cm) |
Hitch pin | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip |
Dump angles | 55 degrees | 55 degrees | 56 degrees | 31 degrees | 46 degrees | 46 degrees | 35/40 degrees | 35/40 degrees |
Maximum tongue weight | 100 lb (45.4 kg) | 100 lb (45.4 kg) | 70 lb (31.75 kg) | 100 lb (45.4 kg) | 50 lb (22 kg) | 100 lb (45.4 kg) | 100 lb (45.4 kg) | 100 lb (45.4 kg) |
Shipping weight with carton | 68 lb (31 kg) | 65 lb (29.5 kg) | 79 lb (35.8 kg) | 110 lb (49.9 kg) | --- | 105 lb (47.6 kg) | 170 lb (77.1 kg) | 240 lb (109 kg) |
Net weight | 65 lb (29 kg) | 55 lb (25 kg) | 72 lb (32.7 kg) | 105 lb (47.6 kg) | 103 lb (47 kg) | 105 lb (47.6 kg) | 150 lb (68 kg) | 220 lb (99.8 kg) |
*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).
**HDPE is compression molded for optimum thickness in all areas and maximum durability.
Utility Carts
Chart below shows vehicle compatibility.
An X indicates cart can be used with the pulling unit.
NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.
7P | 8Y | 10P | 13 | 16YS | 17P | 18 | 21 | |
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z335M, Z345M, Z345R, Z355R, Z375R, Z525E, Z535M, Z540M, Z535R, Z540R, Z720E, Z735E, Z730M, Z735M, Z740R | X | X | ||||||
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180 | X | X | X | X | X | X | X | |
S240 | X | X | X | X | X | X | X | |
LT150, LT160, LT180, LT190, LTR180 | X | X | X | X | X | |||
LX280, LX280AWS, LX289 | X | X | X | X | X | |||
X300, X300R, X304, X310, X320, X324, X340, X360, X330, X350, X350R, X354, X370, X380, X384, X390, X394 | X | X | X | X | X | X | X | |
SST15, SST16, SST18 | X | X | X | |||||
G110 | X | X | X | X | X | X | ||
GT235, GT245 | X | X | X | X | X | X | ||
GX255, GX335, GX345, GX355 | X | X | X | X | X | X | ||
X500, X520, X530, X534, X540 X570, X580, X584, X590 | X | X | X | X | X | X | X | |
X465, X475, X485, X495, X575, X585, X595 | X | X | X | X | X | X | X | X |
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758 | X | X | X | X | X | X | X | X |
For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:
Tractor | Additional weight |
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180 | Two 30-lb (14-kg) wheel weights, front Two 42-lb (19-kg) suitcase weights, rear |
S240 | Two 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear |
LT150, LT160, LT180, LT190, LTR180 | Two 34-lb (15-kg) wheel weights, front Two 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190) |
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394 | Two 34-lb (15-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, rear |
SST15, SST16, SST18 | One 88-lb (40-kg) weight kit, front Three 40-lb (18-kg) weights, rear |
G100 | Two 50-lb (23-kg) wheel weights, rear Two 42-lb (19-kg) suitcase weights, rear |
G110 | Two 50-lb (23-kg) plastic shell rear wheel weights |
GT235, GT245 | Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear |
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590 | Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) wheel plastic shell weights, rear |
X465, X475, X485, X495, X575, X585, X595 | Four 42-lb (19-kg) suitcase weights, front Two 70-lb (32-kg) wheel cast-iron starter weights, rear Four 50-lb (23-kg) cast-iron wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear Six 42-lb (19-kg) suitcase weights, rear |
Please contact a local John Deere dealer for availability and pricing information.
8Y Convertible Poly Utility Cart
Order number: LP22755
Oilite is a trademark of Beemer Precision, Incorporated.
Every owner of a John Deere riding lawn and garden product is a potential customer for a high-quality, affordable utility cart.
Utility carts can be used to haul a variety of materials:
The 10P Utility Cart is designed, painted, and decaled to be compatible with other John Deere equipment:
A convenient foot pedal dump release kit, LP48017, which now comes standard on all 10P and 17P carts is available to retrofit existing poly carts. This kit allows the operator to use both hands to lift the cart bed for more natural and efficient unloading.
Comparison with similar models
Model | Order through | Box capacity (heaped) | Material thickness | Maximum weight | Vehicle compatibility |
7P | Order Zone | 7 cu ft (0.20 m3) | High-density polyethylene (HDPE)** | 450 lb* (204 kg) | EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series |
8Y | Order Zone | 8 cu ft (0.22 m3) | HDPE** | 300 lb* (136 kg) (tow) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
10P | Order Zone | 10 cu ft (0.28 m3) | Polypropylene | 650 lb* (295 kg) | EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series |
13 | Order Zone | 13 cu ft (0.37 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
16YS | Order Zone | 17 cu ft (0.48 m3) | Polypropylene | 800 lb (363 kg), 350 lb (158 kg) when using swivel feature to dump | 100 Series, S240, X300 Series, X500 Series, X700 Series |
17P | Order Zone | 17 cu ft (0.48 m3) | Polypropylene | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
18 | Order Zone | 18 cu ft (0.51 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
21 | Order Zone | 21 cu ft (0.59 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | X700 Series |
*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).
**HDPE is compression molded for optimum thickness in all areas and maximum durability.
7P | 8Y | 10P | 13 | 16YS | 17P | 18 | 21 | |
Box capacity | ||||||||
Heaped | 7 cu ft (0.20 m3) | 8 cu ft (0.22 m3) | 10 cu ft (0.28 m3) | 13 cu ft (0.37 m3) | 17 cu ft (0.48 m3) | 17 cu ft (0.48 m3) | 18 cu ft (0.51 m3) | 21 cu ft (0.59 m3) |
Struck | 5.6 cu ft (0.16 m3) | 6.6 cu ft (0.19 m3) | 8.3 cu ft (0.24 m3) | 10 cu ft (0.28 m3) | 15 cu ft (0.42 m3) | 14 cu ft (0.40 m3) | 15 cu ft (0.42 m3) | 15 cu ft (0.42 m3) |
Maximum weight | 450 lb* (204 kg) | 300 lb* (136 kg) | 650 lb* (295 kg) | 1,000 lb* (454 kg) | 800 lb* (363 kg), 350 lb (158 kg) when using swivel feature to dump | 1,000 lb* (454 kg) | 1,000 lb* (454 kg) | 1,000 lb* (454 kg) |
Box dimensions | ||||||||
Width | 33 in. (84 cm) | 33.68 in. (85.5 cm) | 30.3 in. (77 cm) | 30.25 in. (76.8 cm) | 39.5 in. (100.3 cm) | 39.5 in. (100.3 cm) | 38 in. (96.5 cm) | 48 in. (122 cm) |
Length | 45 in. (114 cm) | 45 in. (114 cm) | 44.5 in. (113 cm) | 48 in. (122 cm) | 58.5 in. (148.6 cm) | 58.5 in. (148.6 cm) | 48 in. (122 cm) | 48 in. (122 cm) |
Depth | 10.5 in. (27 cm) | 10.75 in. (27.3cm) | 12 in. (30.5 cm) | 12 in. (30.5 cm) | 15.5 in. (39.4 cm) | 15.5 in. (39.4 cm) | 18 in. (45.7 cm) | 11 in. (27.9 cm) |
Box construction | Molded | Molded | Molded | Welded | Molded | Molded | Welded | Bolted |
Material | High-density polyethylene (HDPE)** | HDPE** w/UV inhibitor | Polypropylene | 16-gauge, 0.06-in. (1.5-mm) steel | Polypropylene | Polypropylene | 16-gauge, 0.06-in. (1.5-mm) steel | 16-gauge, 0.06-in. (1.5-mm) steel |
Tailgate | None, sloped | None, sloped | None, sloped | Hinged | None, sloped | None, sloped | Hinged | Lift-out/swing-out |
Pneumatic tires | 2 ply | --- | 2 ply | 2 ply | 4 ply | 4 ply | 4 ply | 2 ply |
Size | 13x4-6 | 13x4-6 | 15x6.00-6 | 15x6.00-6 | 16x6.50-8 | 16x6.50-8 | 16x6.50-8 | 20x10.00-8 |
Tread design | Turf | Knobby | Turf | Turf | Turf | Turf | Turf | Turf |
Recommended inflation pressure | 30 psi (207 kPa) | 30 psi (207 kPa) | 14 psi (97 kPa) | 14 psi (97 kPa) | 35 psi (241 kPa) | 28 psi (193 kPa) | 28 psi (193 kPa) | 10 psi (70 kPa) |
Wheel bearings | Iron/Oilite | None | Iron/Oilite | Iron/Oilite | Iron/Oilite | Iron/Oilite | Iron/Oilite | Ball bearings, double sealed |
Grease fittings on wheels | Yes | None | Yes | Yes | Yes | Yes | Yes | None |
Axle diameter | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 1 in. (2.54 cm) | 1 in. (2.54 cm) |
Ground clearance | 5.62 in. (14.3 cm) | 5.25 in. (13.3 cm) | 6.5 in. (16.5 cm) | 6.5 in. (16.5 cm) | 14.25 in. (36.2 cm) | 14.25 in. (36.2 cm) | 7 in. (17.8 cm) | 8.25 in. (21 cm) |
Width, overall | 34 in. (86.4 cm) | 33.68 in. (85.5 cm) | 38 in. (96.5 cm) | 38 in. (96.5 cm) | 39.5 in. (100.3 cm) | 39.5 in. (100.3 cm) | 38 in. (96.5 cm) | 48 in. (122 cm) |
Hitch pin | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip |
Dump angles | 55 degrees | 55 degrees | 56 degrees | 31 degrees | 46 degrees | 46 degrees | 35/40 degrees | 35/40 degrees |
Maximum tongue weight | 100 lb (45.4 kg) | 100 lb (45.4 kg) | 70 lb (31.75 kg) | 100 lb (45.4 kg) | 50 lb (22 kg) | 100 lb (45.4 kg) | 100 lb (45.4 kg) | 100 lb (45.4 kg) |
Shipping weight with carton | 68 lb (31 kg) | 65 lb (29.5 kg) | 79 lb (35.8 kg) | 110 lb (49.9 kg) | --- | 105 lb (47.6 kg) | 170 lb (77.1 kg) | 240 lb (109 kg) |
Net weight | 65 lb (29 kg) | 55 lb (25 kg) | 72 lb (32.7 kg) | 105 lb (47.6 kg) | 103 lb (47 kg) | 105 lb (47.6 kg) | 150 lb (68 kg) | 220 lb (99.8 kg) |
*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).
**HDPE is compression molded for optimum thickness in all areas and maximum durability.
Utility Carts
Chart below shows vehicle compatibility.
An X indicates cart can be used with the pulling unit.
NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.
7P | 8Y | 10P | 13 | 16YS | 17P | 18 | 21 | |
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z335M, Z345M, Z345R, Z355R, Z375R, Z525E, Z535M, Z540M, Z535R, Z540R, Z720E, Z735E, Z730M, Z735M, Z740R | X | X | ||||||
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180 | X | X | X | X | X | X | X | |
S240 | X | X | X | X | X | X | X | |
LT150, LT160, LT180, LT190, LTR180 | X | X | X | X | X | |||
LX280, LX280AWS, LX289 | X | X | X | X | X | |||
X300, X300R, X304, X310, X320, X324, X340, X360, X330, X350, X350R, X354, X370, X380, X384, X390, X394 | X | X | X | X | X | X | X | |
SST15, SST16, SST18 | X | X | X | |||||
G110 | X | X | X | X | X | X | ||
GT235, GT245 | X | X | X | X | X | X | ||
GX255, GX335, GX345, GX355 | X | X | X | X | X | X | ||
X500, X520, X530, X534, X540 X570, X580, X584, X590 | X | X | X | X | X | X | X | |
X465, X475, X485, X495, X575, X585, X595 | X | X | X | X | X | X | X | X |
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758 | X | X | X | X | X | X | X | X |
For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:
Tractor | Additional weight |
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180 | Two 30-lb (14-kg) wheel weights, front Two 42-lb (19-kg) suitcase weights, rear |
S240 | Two 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear |
LT150, LT160, LT180, LT190, LTR180 | Two 34-lb (15-kg) wheel weights, front Two 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190) |
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394 | Two 34-lb (15-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, rear |
SST15, SST16, SST18 | One 88-lb (40-kg) weight kit, front Three 40-lb (18-kg) weights, rear |
G100 | Two 50-lb (23-kg) wheel weights, rear Two 42-lb (19-kg) suitcase weights, rear |
G110 | Two 50-lb (23-kg) plastic shell rear wheel weights |
GT235, GT245 | Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear |
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590 | Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) wheel plastic shell weights, rear |
X465, X475, X485, X495, X575, X585, X595 | Four 42-lb (19-kg) suitcase weights, front Two 70-lb (32-kg) wheel cast-iron starter weights, rear Four 50-lb (23-kg) cast-iron wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear Six 42-lb (19-kg) suitcase weights, rear |
Ordering information
Please contact a local John Deere dealer for availability and pricing information.
10P Poly Utility Cart
Order number: LPPCT10JD
Oilite is a trademark of Beemer Precision, Incorporated.
Every owner of a John Deere riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials, including firewood, lawn debris, dirt, sand, mulch, garden tools, plants, and bushes.
Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.
For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. See the appropriate vehicle pages for the weight of the vehicle and the mower deck.
Welded box construction provides maximum reliability:
Wheels are mounted on a solid, one-piece axle for durability.
Iron/Oilite® wheel bearings with grease fittings provide lubrication for long life.
Pneumatic tires offer:
Turf-tread tires are used on the 13 Utility Cart.
Deluxe tailgate is hinged for easy emptying and can also be quickly removed without the use of tools.
A large-diameter hitch pin provides plenty of strength:
The easy-to-use latch allows tilting the bed for easier unloading:
Comparison with similar models
Model | Order through | Box capacity (heaped) | Material thickness | Maximum weight | Vehicle compatibility |
7P | Order Zone | 7 cu ft (0.20 m3) | High-density polyethylene (HDPE)** | 450 lb* (204 kg) | EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series |
8Y | Order Zone | 8 cu ft (0.22 m3) | HDPE** | 300 lb* (136 kg) (tow) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
10P | Order Zone | 10 cu ft (0.28 m3) | Polypropylene | 650 lb* (295 kg) | EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series |
13 | Order Zone | 13 cu ft (0.37 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
16YS | Order Zone | 17 cu ft (0.48 m3) | Polypropylene | 800 lb (363 kg), 350 lb (158 kg) when using swivel feature to dump | 100 Series, S240, X300 Series, X500 Series, X700 Series |
17P | Order Zone | 17 cu ft (0.48 m3) | Polypropylene | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
18 | Order Zone | 18 cu ft (0.51 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
21 | Order Zone | 21 cu ft (0.59 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | X700 Series |
*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).
**HDPE is compression molded for optimum thickness in all areas and maximum durability.
7P | 8Y | 10P | 13 | 16YS | 17P | 18 | 21 | |
Box capacity | ||||||||
Heaped | 7 cu ft (0.20 m3) | 8 cu ft (0.22 m3) | 10 cu ft (0.28 m3) | 13 cu ft (0.37 m3) | 17 cu ft (0.48 m3) | 17 cu ft (0.48 m3) | 18 cu ft (0.51 m3) | 21 cu ft (0.59 m3) |
Struck | 5.6 cu ft (0.16 m3) | 6.6 cu ft (0.19 m3) | 8.3 cu ft (0.24 m3) | 10 cu ft (0.28 m3) | 15 cu ft (0.42 m3) | 14 cu ft (0.40 m3) | 15 cu ft (0.42 m3) | 15 cu ft (0.42 m3) |
Maximum weight | 450 lb* (204 kg) | 300 lb* (136 kg) | 650 lb* (295 kg) | 1,000 lb* (454 kg) | 800 lb* (363 kg), 350 lb (158 kg) when using swivel feature to dump | 1,000 lb* (454 kg) | 1,000 lb* (454 kg) | 1,000 lb* (454 kg) |
Box dimensions | ||||||||
Width | 33 in. (84 cm) | 33.68 in. (85.5 cm) | 30.3 in. (77 cm) | 30.25 in. (76.8 cm) | 39.5 in. (100.3 cm) | 39.5 in. (100.3 cm) | 38 in. (96.5 cm) | 48 in. (122 cm) |
Length | 45 in. (114 cm) | 45 in. (114 cm) | 44.5 in. (113 cm) | 48 in. (122 cm) | 58.5 in. (148.6 cm) | 58.5 in. (148.6 cm) | 48 in. (122 cm) | 48 in. (122 cm) |
Depth | 10.5 in. (27 cm) | 10.75 in. (27.3cm) | 12 in. (30.5 cm) | 12 in. (30.5 cm) | 15.5 in. (39.4 cm) | 15.5 in. (39.4 cm) | 18 in. (45.7 cm) | 11 in. (27.9 cm) |
Box construction | Molded | Molded | Molded | Welded | Molded | Molded | Welded | Bolted |
Material | High-density polyethylene (HDPE)** | HDPE** w/UV inhibitor | Polypropylene | 16-gauge, 0.06-in. (1.5-mm) steel | Polypropylene | Polypropylene | 16-gauge, 0.06-in. (1.5-mm) steel | 16-gauge, 0.06-in. (1.5-mm) steel |
Tailgate | None, sloped | None, sloped | None, sloped | Hinged | None, sloped | None, sloped | Hinged | Lift-out/swing-out |
Pneumatic tires | 2 ply | --- | 2 ply | 2 ply | 4 ply | 4 ply | 4 ply | 2 ply |
Size | 13x4-6 | 13x4-6 | 15x6.00-6 | 15x6.00-6 | 16x6.50-8 | 16x6.50-8 | 16x6.50-8 | 20x10.00-8 |
Tread design | Turf | Knobby | Turf | Turf | Turf | Turf | Turf | Turf |
Recommended inflation pressure | 30 psi (207 kPa) | 30 psi (207 kPa) | 14 psi (97 kPa) | 14 psi (97 kPa) | 35 psi (241 kPa) | 28 psi (193 kPa) | 28 psi (193 kPa) | 10 psi (70 kPa) |
Wheel bearings | Iron/Oilite | None | Iron/Oilite | Iron/Oilite | Iron/Oilite | Iron/Oilite | Iron/Oilite | Ball bearings, double sealed |
Grease fittings on wheels | Yes | None | Yes | Yes | Yes | Yes | Yes | None |
Axle diameter | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 1 in. (2.54 cm) | 1 in. (2.54 cm) |
Ground clearance | 5.62 in. (14.3 cm) | 5.25 in. (13.3 cm) | 6.5 in. (16.5 cm) | 6.5 in. (16.5 cm) | 14.25 in. (36.2 cm) | 14.25 in. (36.2 cm) | 7 in. (17.8 cm) | 8.25 in. (21 cm) |
Width, overall | 34 in. (86.4 cm) | 33.68 in. (85.5 cm) | 38 in. (96.5 cm) | 38 in. (96.5 cm) | 39.5 in. (100.3 cm) | 39.5 in. (100.3 cm) | 38 in. (96.5 cm) | 48 in. (122 cm) |
Hitch pin | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip |
Dump angles | 55 degrees | 55 degrees | 56 degrees | 31 degrees | 46 degrees | 46 degrees | 35/40 degrees | 35/40 degrees |
Maximum tongue weight | 100 lb (45.4 kg) | 100 lb (45.4 kg) | 70 lb (31.75 kg) | 100 lb (45.4 kg) | 50 lb (22 kg) | 100 lb (45.4 kg) | 100 lb (45.4 kg) | 100 lb (45.4 kg) |
Shipping weight with carton | 68 lb (31 kg) | 65 lb (29.5 kg) | 79 lb (35.8 kg) | 110 lb (49.9 kg) | --- | 105 lb (47.6 kg) | 170 lb (77.1 kg) | 240 lb (109 kg) |
Net weight | 65 lb (29 kg) | 55 lb (25 kg) | 72 lb (32.7 kg) | 105 lb (47.6 kg) | 103 lb (47 kg) | 105 lb (47.6 kg) | 150 lb (68 kg) | 220 lb (99.8 kg) |
*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).
**HDPE is compression molded for optimum thickness in all areas and maximum durability.
Utility Carts
Chart below shows vehicle compatibility.
An X indicates cart can be used with the pulling unit.
NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.
7P | 8Y | 10P | 13 | 16YS | 17P | 18 | 21 | |
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z335M, Z345M, Z345R, Z355R, Z375R, Z525E, Z535M, Z540M, Z535R, Z540R, Z720E, Z735E, Z730M, Z735M, Z740R | X | X | ||||||
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180 | X | X | X | X | X | X | X | |
S240 | X | X | X | X | X | X | X | |
LT150, LT160, LT180, LT190, LTR180 | X | X | X | X | X | |||
LX280, LX280AWS, LX289 | X | X | X | X | X | |||
X300, X300R, X304, X310, X320, X324, X340, X360, X330, X350, X350R, X354, X370, X380, X384, X390, X394 | X | X | X | X | X | X | X | |
SST15, SST16, SST18 | X | X | X | |||||
G110 | X | X | X | X | X | X | ||
GT235, GT245 | X | X | X | X | X | X | ||
GX255, GX335, GX345, GX355 | X | X | X | X | X | X | ||
X500, X520, X530, X534, X540 X570, X580, X584, X590 | X | X | X | X | X | X | X | |
X465, X475, X485, X495, X575, X585, X595 | X | X | X | X | X | X | X | X |
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758 | X | X | X | X | X | X | X | X |
For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:
Tractor | Additional weight |
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180 | Two 30-lb (14-kg) wheel weights, front Two 42-lb (19-kg) suitcase weights, rear |
S240 | Two 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear |
LT150, LT160, LT180, LT190, LTR180 | Two 34-lb (15-kg) wheel weights, front Two 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190) |
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394 | Two 34-lb (15-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, rear |
SST15, SST16, SST18 | One 88-lb (40-kg) weight kit, front Three 40-lb (18-kg) weights, rear |
G100 | Two 50-lb (23-kg) wheel weights, rear Two 42-lb (19-kg) suitcase weights, rear |
G110 | Two 50-lb (23-kg) plastic shell rear wheel weights |
GT235, GT245 | Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear |
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590 | Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) wheel plastic shell weights, rear |
X465, X475, X485, X495, X575, X585, X595 | Four 42-lb (19-kg) suitcase weights, front Two 70-lb (32-kg) wheel cast-iron starter weights, rear Four 50-lb (23-kg) cast-iron wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear Six 42-lb (19-kg) suitcase weights, rear |
Please contact a local John Deere dealer for availability and pricing information.
13 Utility Cart
Order number: LPHDC13JD
Oilite is a trademark of Beemer Precision, Incorporated.
The 17-cu-ft (0.48-m³), 800-lb (363-kg) capacity or 350 lb (158 kg) when using swivel feature to dump 16YS Swivel Cart is unique in the lineup of John Deere carts in that it can be swiveled 120 degrees to either side for easier unloading. The operator can simply pull up next to where they want to dump the material and swivel the cart, eliminating the need to back up the cart.
Key features include:
NOTE: Do not exceed 350 lb (158 kg) weight capacity when using swivel feature to dump.
Every owner of a John Deere riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials including firewood, lawn debris, sand, dirt, mulch, garden tools, plants, and bushes. Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.
NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. See the appropriate vehicle pages for the weight of the vehicle and the mower deck.
Comparison with similar models
Model | Order through | Box capacity (heaped) | Material thickness | Maximum weight | Vehicle compatibility |
7P | Order Zone | 7 cu ft (0.20 m3) | High-density polyethylene (HDPE)** | 450 lb* (204 kg) | EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series |
8Y | Order Zone | 8 cu ft (0.22 m3) | HDPE** | 300 lb* (136 kg) (tow) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
10P | Order Zone | 10 cu ft (0.28 m3) | Polypropylene | 650 lb* (295 kg) | EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series |
13 | Order Zone | 13 cu ft (0.37 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
16YS | Order Zone | 17 cu ft (0.48 m3) | Polypropylene | 800 lb (363 kg), 350 lb (158 kg) when using swivel feature to dump | 100 Series, S240, X300 Series, X500 Series, X700 Series |
17P | Order Zone | 17 cu ft (0.48 m3) | Polypropylene | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
18 | Order Zone | 18 cu ft (0.51 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
21 | Order Zone | 21 cu ft (0.59 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | X700 Series |
*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).
**HDPE is compression molded for optimum thickness in all areas and maximum durability.
7P | 8Y | 10P | 13 | 16YS | 17P | 18 | 21 | |
Box capacity | ||||||||
Heaped | 7 cu ft (0.20 m3) | 8 cu ft (0.22 m3) | 10 cu ft (0.28 m3) | 13 cu ft (0.37 m3) | 17 cu ft (0.48 m3) | 17 cu ft (0.48 m3) | 18 cu ft (0.51 m3) | 21 cu ft (0.59 m3) |
Struck | 5.6 cu ft (0.16 m3) | 6.6 cu ft (0.19 m3) | 8.3 cu ft (0.24 m3) | 10 cu ft (0.28 m3) | 15 cu ft (0.42 m3) | 14 cu ft (0.40 m3) | 15 cu ft (0.42 m3) | 15 cu ft (0.42 m3) |
Maximum weight | 450 lb* (204 kg) | 300 lb* (136 kg) | 650 lb* (295 kg) | 1,000 lb* (454 kg) | 800 lb* (363 kg), 350 lb (158 kg) when using swivel feature to dump | 1,000 lb* (454 kg) | 1,000 lb* (454 kg) | 1,000 lb* (454 kg) |
Box dimensions | ||||||||
Width | 33 in. (84 cm) | 33.68 in. (85.5 cm) | 30.3 in. (77 cm) | 30.25 in. (76.8 cm) | 39.5 in. (100.3 cm) | 39.5 in. (100.3 cm) | 38 in. (96.5 cm) | 48 in. (122 cm) |
Length | 45 in. (114 cm) | 45 in. (114 cm) | 44.5 in. (113 cm) | 48 in. (122 cm) | 58.5 in. (148.6 cm) | 58.5 in. (148.6 cm) | 48 in. (122 cm) | 48 in. (122 cm) |
Depth | 10.5 in. (27 cm) | 10.75 in. (27.3cm) | 12 in. (30.5 cm) | 12 in. (30.5 cm) | 15.5 in. (39.4 cm) | 15.5 in. (39.4 cm) | 18 in. (45.7 cm) | 11 in. (27.9 cm) |
Box construction | Molded | Molded | Molded | Welded | Molded | Molded | Welded | Bolted |
Material | High-density polyethylene (HDPE)** | HDPE** w/UV inhibitor | Polypropylene | 16-gauge, 0.06-in. (1.5-mm) steel | Polypropylene | Polypropylene | 16-gauge, 0.06-in. (1.5-mm) steel | 16-gauge, 0.06-in. (1.5-mm) steel |
Tailgate | None, sloped | None, sloped | None, sloped | Hinged | None, sloped | None, sloped | Hinged | Lift-out/swing-out |
Pneumatic tires | 2 ply | --- | 2 ply | 2 ply | 4 ply | 4 ply | 4 ply | 2 ply |
Size | 13x4-6 | 13x4-6 | 15x6.00-6 | 15x6.00-6 | 16x6.50-8 | 16x6.50-8 | 16x6.50-8 | 20x10.00-8 |
Tread design | Turf | Knobby | Turf | Turf | Turf | Turf | Turf | Turf |
Recommended inflation pressure | 30 psi (207 kPa) | 30 psi (207 kPa) | 14 psi (97 kPa) | 14 psi (97 kPa) | 35 psi (241 kPa) | 28 psi (193 kPa) | 28 psi (193 kPa) | 10 psi (70 kPa) |
Wheel bearings | Iron/Oilite | None | Iron/Oilite | Iron/Oilite | Iron/Oilite | Iron/Oilite | Iron/Oilite | Ball bearings, double sealed |
Grease fittings on wheels | Yes | None | Yes | Yes | Yes | Yes | Yes | None |
Axle diameter | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 1 in. (2.54 cm) | 1 in. (2.54 cm) |
Ground clearance | 5.62 in. (14.3 cm) | 5.25 in. (13.3 cm) | 6.5 in. (16.5 cm) | 6.5 in. (16.5 cm) | 14.25 in. (36.2 cm) | 14.25 in. (36.2 cm) | 7 in. (17.8 cm) | 8.25 in. (21 cm) |
Width, overall | 34 in. (86.4 cm) | 33.68 in. (85.5 cm) | 38 in. (96.5 cm) | 38 in. (96.5 cm) | 39.5 in. (100.3 cm) | 39.5 in. (100.3 cm) | 38 in. (96.5 cm) | 48 in. (122 cm) |
Hitch pin | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip |
Dump angles | 55 degrees | 55 degrees | 56 degrees | 31 degrees | 46 degrees | 46 degrees | 35/40 degrees | 35/40 degrees |
Maximum tongue weight | 100 lb (45.4 kg) | 100 lb (45.4 kg) | 70 lb (31.75 kg) | 100 lb (45.4 kg) | 50 lb (22 kg) | 100 lb (45.4 kg) | 100 lb (45.4 kg) | 100 lb (45.4 kg) |
Shipping weight with carton | 68 lb (31 kg) | 65 lb (29.5 kg) | 79 lb (35.8 kg) | 110 lb (49.9 kg) | --- | 105 lb (47.6 kg) | 170 lb (77.1 kg) | 240 lb (109 kg) |
Net weight | 65 lb (29 kg) | 55 lb (25 kg) | 72 lb (32.7 kg) | 105 lb (47.6 kg) | 103 lb (47 kg) | 105 lb (47.6 kg) | 150 lb (68 kg) | 220 lb (99.8 kg) |
*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).
**HDPE is compression molded for optimum thickness in all areas and maximum durability.
Utility Carts
Chart below shows vehicle compatibility.
An X indicates cart can be used with the pulling unit.
NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.
7P | 8Y | 10P | 13 | 16YS | 17P | 18 | 21 | |
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z335M, Z345M, Z345R, Z355R, Z375R, Z525E, Z535M, Z540M, Z535R, Z540R, Z720E, Z735E, Z730M, Z735M, Z740R | X | X | ||||||
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180 | X | X | X | X | X | X | X | |
S240 | X | X | X | X | X | X | X | |
LT150, LT160, LT180, LT190, LTR180 | X | X | X | X | X | |||
LX280, LX280AWS, LX289 | X | X | X | X | X | |||
X300, X300R, X304, X310, X320, X324, X340, X360, X330, X350, X350R, X354, X370, X380, X384, X390, X394 | X | X | X | X | X | X | X | |
SST15, SST16, SST18 | X | X | X | |||||
G110 | X | X | X | X | X | X | ||
GT235, GT245 | X | X | X | X | X | X | ||
GX255, GX335, GX345, GX355 | X | X | X | X | X | X | ||
X500, X520, X530, X534, X540 X570, X580, X584, X590 | X | X | X | X | X | X | X | |
X465, X475, X485, X495, X575, X585, X595 | X | X | X | X | X | X | X | X |
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758 | X | X | X | X | X | X | X | X |
For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:
Tractor | Additional weight |
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180 | Two 30-lb (14-kg) wheel weights, front Two 42-lb (19-kg) suitcase weights, rear |
S240 | Two 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear |
LT150, LT160, LT180, LT190, LTR180 | Two 34-lb (15-kg) wheel weights, front Two 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190) |
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394 | Two 34-lb (15-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, rear |
SST15, SST16, SST18 | One 88-lb (40-kg) weight kit, front Three 40-lb (18-kg) weights, rear |
G100 | Two 50-lb (23-kg) wheel weights, rear Two 42-lb (19-kg) suitcase weights, rear |
G110 | Two 50-lb (23-kg) plastic shell rear wheel weights |
GT235, GT245 | Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear |
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590 | Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) wheel plastic shell weights, rear |
X465, X475, X485, X495, X575, X585, X595 | Four 42-lb (19-kg) suitcase weights, front Two 70-lb (32-kg) wheel cast-iron starter weights, rear Four 50-lb (23-kg) cast-iron wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear Six 42-lb (19-kg) suitcase weights, rear |
Please contact a local John Deere dealer for availability and pricing information.
16YS Swivel Cart
Order number: LP68186
Oilite is a trademark of Beemer Precision Incorporated.
Every owner of a John Deere riding lawn and garden product is a potential user of a high-quality, affordable utility cart.
Utility carts can be used to haul a variety of materials:
Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.
Key features of the 17P Utility Cart:
A convenient foot pedal dump release kit, LP48017, which now comes standard on all 10P and 17P carts is available to retrofit existing poly carts. This kit allows the operator to use both hands to lift the cart bed for more natural and efficient unloading.
Comparison with similar models
Model | Order through | Box capacity (heaped) | Material thickness | Maximum weight | Vehicle compatibility |
7P | Order Zone | 7 cu ft (0.20 m3) | High-density polyethylene (HDPE)** | 450 lb* (204 kg) | EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series |
8Y | Order Zone | 8 cu ft (0.22 m3) | HDPE** | 300 lb* (136 kg) (tow) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
10P | Order Zone | 10 cu ft (0.28 m3) | Polypropylene | 650 lb* (295 kg) | EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series |
13 | Order Zone | 13 cu ft (0.37 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
16YS | Order Zone | 17 cu ft (0.48 m3) | Polypropylene | 800 lb (363 kg), 350 lb (158 kg) when using swivel feature to dump | 100 Series, S240, X300 Series, X500 Series, X700 Series |
17P | Order Zone | 17 cu ft (0.48 m3) | Polypropylene | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
18 | Order Zone | 18 cu ft (0.51 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
21 | Order Zone | 21 cu ft (0.59 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | X700 Series |
*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).
**HDPE is compression molded for optimum thickness in all areas and maximum durability.
7P | 8Y | 10P | 13 | 16YS | 17P | 18 | 21 | |
Box capacity | ||||||||
Heaped | 7 cu ft (0.20 m3) | 8 cu ft (0.22 m3) | 10 cu ft (0.28 m3) | 13 cu ft (0.37 m3) | 17 cu ft (0.48 m3) | 17 cu ft (0.48 m3) | 18 cu ft (0.51 m3) | 21 cu ft (0.59 m3) |
Struck | 5.6 cu ft (0.16 m3) | 6.6 cu ft (0.19 m3) | 8.3 cu ft (0.24 m3) | 10 cu ft (0.28 m3) | 15 cu ft (0.42 m3) | 14 cu ft (0.40 m3) | 15 cu ft (0.42 m3) | 15 cu ft (0.42 m3) |
Maximum weight | 450 lb* (204 kg) | 300 lb* (136 kg) | 650 lb* (295 kg) | 1,000 lb* (454 kg) | 800 lb* (363 kg), 350 lb (158 kg) when using swivel feature to dump | 1,000 lb* (454 kg) | 1,000 lb* (454 kg) | 1,000 lb* (454 kg) |
Box dimensions | ||||||||
Width | 33 in. (84 cm) | 33.68 in. (85.5 cm) | 30.3 in. (77 cm) | 30.25 in. (76.8 cm) | 39.5 in. (100.3 cm) | 39.5 in. (100.3 cm) | 38 in. (96.5 cm) | 48 in. (122 cm) |
Length | 45 in. (114 cm) | 45 in. (114 cm) | 44.5 in. (113 cm) | 48 in. (122 cm) | 58.5 in. (148.6 cm) | 58.5 in. (148.6 cm) | 48 in. (122 cm) | 48 in. (122 cm) |
Depth | 10.5 in. (27 cm) | 10.75 in. (27.3cm) | 12 in. (30.5 cm) | 12 in. (30.5 cm) | 15.5 in. (39.4 cm) | 15.5 in. (39.4 cm) | 18 in. (45.7 cm) | 11 in. (27.9 cm) |
Box construction | Molded | Molded | Molded | Welded | Molded | Molded | Welded | Bolted |
Material | High-density polyethylene (HDPE)** | HDPE** w/UV inhibitor | Polypropylene | 16-gauge, 0.06-in. (1.5-mm) steel | Polypropylene | Polypropylene | 16-gauge, 0.06-in. (1.5-mm) steel | 16-gauge, 0.06-in. (1.5-mm) steel |
Tailgate | None, sloped | None, sloped | None, sloped | Hinged | None, sloped | None, sloped | Hinged | Lift-out/swing-out |
Pneumatic tires | 2 ply | --- | 2 ply | 2 ply | 4 ply | 4 ply | 4 ply | 2 ply |
Size | 13x4-6 | 13x4-6 | 15x6.00-6 | 15x6.00-6 | 16x6.50-8 | 16x6.50-8 | 16x6.50-8 | 20x10.00-8 |
Tread design | Turf | Knobby | Turf | Turf | Turf | Turf | Turf | Turf |
Recommended inflation pressure | 30 psi (207 kPa) | 30 psi (207 kPa) | 14 psi (97 kPa) | 14 psi (97 kPa) | 35 psi (241 kPa) | 28 psi (193 kPa) | 28 psi (193 kPa) | 10 psi (70 kPa) |
Wheel bearings | Iron/Oilite | None | Iron/Oilite | Iron/Oilite | Iron/Oilite | Iron/Oilite | Iron/Oilite | Ball bearings, double sealed |
Grease fittings on wheels | Yes | None | Yes | Yes | Yes | Yes | Yes | None |
Axle diameter | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 1 in. (2.54 cm) | 1 in. (2.54 cm) |
Ground clearance | 5.62 in. (14.3 cm) | 5.25 in. (13.3 cm) | 6.5 in. (16.5 cm) | 6.5 in. (16.5 cm) | 14.25 in. (36.2 cm) | 14.25 in. (36.2 cm) | 7 in. (17.8 cm) | 8.25 in. (21 cm) |
Width, overall | 34 in. (86.4 cm) | 33.68 in. (85.5 cm) | 38 in. (96.5 cm) | 38 in. (96.5 cm) | 39.5 in. (100.3 cm) | 39.5 in. (100.3 cm) | 38 in. (96.5 cm) | 48 in. (122 cm) |
Hitch pin | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip |
Dump angles | 55 degrees | 55 degrees | 56 degrees | 31 degrees | 46 degrees | 46 degrees | 35/40 degrees | 35/40 degrees |
Maximum tongue weight | 100 lb (45.4 kg) | 100 lb (45.4 kg) | 70 lb (31.75 kg) | 100 lb (45.4 kg) | 50 lb (22 kg) | 100 lb (45.4 kg) | 100 lb (45.4 kg) | 100 lb (45.4 kg) |
Shipping weight with carton | 68 lb (31 kg) | 65 lb (29.5 kg) | 79 lb (35.8 kg) | 110 lb (49.9 kg) | --- | 105 lb (47.6 kg) | 170 lb (77.1 kg) | 240 lb (109 kg) |
Net weight | 65 lb (29 kg) | 55 lb (25 kg) | 72 lb (32.7 kg) | 105 lb (47.6 kg) | 103 lb (47 kg) | 105 lb (47.6 kg) | 150 lb (68 kg) | 220 lb (99.8 kg) |
*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).
**HDPE is compression molded for optimum thickness in all areas and maximum durability.
Utility Carts
Chart below shows vehicle compatibility.
An X indicates cart can be used with the pulling unit.
NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.
7P | 8Y | 10P | 13 | 16YS | 17P | 18 | 21 | |
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z335M, Z345M, Z345R, Z355R, Z375R, Z525E, Z535M, Z540M, Z535R, Z540R, Z720E, Z735E, Z730M, Z735M, Z740R | X | X | ||||||
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180 | X | X | X | X | X | X | X | |
S240 | X | X | X | X | X | X | X | |
LT150, LT160, LT180, LT190, LTR180 | X | X | X | X | X | |||
LX280, LX280AWS, LX289 | X | X | X | X | X | |||
X300, X300R, X304, X310, X320, X324, X340, X360, X330, X350, X350R, X354, X370, X380, X384, X390, X394 | X | X | X | X | X | X | X | |
SST15, SST16, SST18 | X | X | X | |||||
G110 | X | X | X | X | X | X | ||
GT235, GT245 | X | X | X | X | X | X | ||
GX255, GX335, GX345, GX355 | X | X | X | X | X | X | ||
X500, X520, X530, X534, X540 X570, X580, X584, X590 | X | X | X | X | X | X | X | |
X465, X475, X485, X495, X575, X585, X595 | X | X | X | X | X | X | X | X |
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758 | X | X | X | X | X | X | X | X |
For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:
Tractor | Additional weight |
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180 | Two 30-lb (14-kg) wheel weights, front Two 42-lb (19-kg) suitcase weights, rear |
S240 | Two 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear |
LT150, LT160, LT180, LT190, LTR180 | Two 34-lb (15-kg) wheel weights, front Two 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190) |
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394 | Two 34-lb (15-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, rear |
SST15, SST16, SST18 | One 88-lb (40-kg) weight kit, front Three 40-lb (18-kg) weights, rear |
G100 | Two 50-lb (23-kg) wheel weights, rear Two 42-lb (19-kg) suitcase weights, rear |
G110 | Two 50-lb (23-kg) plastic shell rear wheel weights |
GT235, GT245 | Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear |
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590 | Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) wheel plastic shell weights, rear |
X465, X475, X485, X495, X575, X585, X595 | Four 42-lb (19-kg) suitcase weights, front Two 70-lb (32-kg) wheel cast-iron starter weights, rear Four 50-lb (23-kg) cast-iron wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear Six 42-lb (19-kg) suitcase weights, rear |
Please contact a local John Deere dealer for availability and pricing information.
17P Utility Cart
Order number: LPPCT17JD
Oilite is a trademark of Beemer Precision Incorporated.
Everyone who owns a John Deere riding lawn and garden product is a potential user of a high-quality affordable utility cart.
Utility carts can be used to haul a variety of materials:
Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.
Durable 18-gauge, 0.05-in. (1.2-mm) (10S) or 16-gauge, 0.06-in. (1.5-mm) (16S) steel components are bolted together.
Recessed bolts are used in the bottom of the box, so they will not interfere with emptying the cart.
The deluxe tailgate is hinged for easy emptying and can also be quickly removed without the use of tools.
Comparison with similar models
Model | Order through | Box capacity (heaped) | Material thickness | Maximum weight | Vehicle compatibility |
7P | Order Zone | 7 cu ft (0.20 m3) | High-density polyethylene (HDPE)** | 450 lb* (204 kg) | EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series |
8Y | Order Zone | 8 cu ft (0.22 m3) | HDPE** | 300 lb* (136 kg) (tow) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
10P | Order Zone | 10 cu ft (0.28 m3) | Polypropylene | 650 lb* (295 kg) | EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series |
13 | Order Zone | 13 cu ft (0.37 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
16YS | Order Zone | 17 cu ft (0.48 m3) | Polypropylene | 800 lb (363 kg), 350 lb (158 kg) when using swivel feature to dump | 100 Series, S240, X300 Series, X500 Series, X700 Series |
17P | Order Zone | 17 cu ft (0.48 m3) | Polypropylene | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
18 | Order Zone | 18 cu ft (0.51 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | 100 Series, S240, X300 Series, X500 Series, X700 Series |
21 | Order Zone | 21 cu ft (0.59 m3) | 16-gauge, 0.06-in. (1.5-mm) steel | 1,000 lb* (454 kg) | X700 Series |
*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).
**HDPE is compression molded for optimum thickness in all areas and maximum durability.
7P | 8Y | 10P | 13 | 16YS | 17P | 18 | 21 | |
Box capacity | ||||||||
Heaped | 7 cu ft (0.20 m3) | 8 cu ft (0.22 m3) | 10 cu ft (0.28 m3) | 13 cu ft (0.37 m3) | 17 cu ft (0.48 m3) | 17 cu ft (0.48 m3) | 18 cu ft (0.51 m3) | 21 cu ft (0.59 m3) |
Struck | 5.6 cu ft (0.16 m3) | 6.6 cu ft (0.19 m3) | 8.3 cu ft (0.24 m3) | 10 cu ft (0.28 m3) | 15 cu ft (0.42 m3) | 14 cu ft (0.40 m3) | 15 cu ft (0.42 m3) | 15 cu ft (0.42 m3) |
Maximum weight | 450 lb* (204 kg) | 300 lb* (136 kg) | 650 lb* (295 kg) | 1,000 lb* (454 kg) | 800 lb* (363 kg), 350 lb (158 kg) when using swivel feature to dump | 1,000 lb* (454 kg) | 1,000 lb* (454 kg) | 1,000 lb* (454 kg) |
Box dimensions | ||||||||
Width | 33 in. (84 cm) | 33.68 in. (85.5 cm) | 30.3 in. (77 cm) | 30.25 in. (76.8 cm) | 39.5 in. (100.3 cm) | 39.5 in. (100.3 cm) | 38 in. (96.5 cm) | 48 in. (122 cm) |
Length | 45 in. (114 cm) | 45 in. (114 cm) | 44.5 in. (113 cm) | 48 in. (122 cm) | 58.5 in. (148.6 cm) | 58.5 in. (148.6 cm) | 48 in. (122 cm) | 48 in. (122 cm) |
Depth | 10.5 in. (27 cm) | 10.75 in. (27.3cm) | 12 in. (30.5 cm) | 12 in. (30.5 cm) | 15.5 in. (39.4 cm) | 15.5 in. (39.4 cm) | 18 in. (45.7 cm) | 11 in. (27.9 cm) |
Box construction | Molded | Molded | Molded | Welded | Molded | Molded | Welded | Bolted |
Material | High-density polyethylene (HDPE)** | HDPE** w/UV inhibitor | Polypropylene | 16-gauge, 0.06-in. (1.5-mm) steel | Polypropylene | Polypropylene | 16-gauge, 0.06-in. (1.5-mm) steel | 16-gauge, 0.06-in. (1.5-mm) steel |
Tailgate | None, sloped | None, sloped | None, sloped | Hinged | None, sloped | None, sloped | Hinged | Lift-out/swing-out |
Pneumatic tires | 2 ply | --- | 2 ply | 2 ply | 4 ply | 4 ply | 4 ply | 2 ply |
Size | 13x4-6 | 13x4-6 | 15x6.00-6 | 15x6.00-6 | 16x6.50-8 | 16x6.50-8 | 16x6.50-8 | 20x10.00-8 |
Tread design | Turf | Knobby | Turf | Turf | Turf | Turf | Turf | Turf |
Recommended inflation pressure | 30 psi (207 kPa) | 30 psi (207 kPa) | 14 psi (97 kPa) | 14 psi (97 kPa) | 35 psi (241 kPa) | 28 psi (193 kPa) | 28 psi (193 kPa) | 10 psi (70 kPa) |
Wheel bearings | Iron/Oilite | None | Iron/Oilite | Iron/Oilite | Iron/Oilite | Iron/Oilite | Iron/Oilite | Ball bearings, double sealed |
Grease fittings on wheels | Yes | None | Yes | Yes | Yes | Yes | Yes | None |
Axle diameter | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 0.75 in. (1.905 cm) | 1 in. (2.54 cm) | 1 in. (2.54 cm) |
Ground clearance | 5.62 in. (14.3 cm) | 5.25 in. (13.3 cm) | 6.5 in. (16.5 cm) | 6.5 in. (16.5 cm) | 14.25 in. (36.2 cm) | 14.25 in. (36.2 cm) | 7 in. (17.8 cm) | 8.25 in. (21 cm) |
Width, overall | 34 in. (86.4 cm) | 33.68 in. (85.5 cm) | 38 in. (96.5 cm) | 38 in. (96.5 cm) | 39.5 in. (100.3 cm) | 39.5 in. (100.3 cm) | 38 in. (96.5 cm) | 48 in. (122 cm) |
Hitch pin | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip | Pin/spring clip |
Dump angles | 55 degrees | 55 degrees | 56 degrees | 31 degrees | 46 degrees | 46 degrees | 35/40 degrees | 35/40 degrees |
Maximum tongue weight | 100 lb (45.4 kg) | 100 lb (45.4 kg) | 70 lb (31.75 kg) | 100 lb (45.4 kg) | 50 lb (22 kg) | 100 lb (45.4 kg) | 100 lb (45.4 kg) | 100 lb (45.4 kg) |
Shipping weight with carton | 68 lb (31 kg) | 65 lb (29.5 kg) | 79 lb (35.8 kg) | 110 lb (49.9 kg) | --- | 105 lb (47.6 kg) | 170 lb (77.1 kg) | 240 lb (109 kg) |
Net weight | 65 lb (29 kg) | 55 lb (25 kg) | 72 lb (32.7 kg) | 105 lb (47.6 kg) | 103 lb (47 kg) | 105 lb (47.6 kg) | 150 lb (68 kg) | 220 lb (99.8 kg) |
*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).
**HDPE is compression molded for optimum thickness in all areas and maximum durability.
Utility Carts
Chart below shows vehicle compatibility.
An X indicates cart can be used with the pulling unit.
NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.
7P | 8Y | 10P | 13 | 16YS | 17P | 18 | 21 | |
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z335M, Z345M, Z345R, Z355R, Z375R, Z525E, Z535M, Z540M, Z535R, Z540R, Z720E, Z735E, Z730M, Z735M, Z740R | X | X | ||||||
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180 | X | X | X | X | X | X | X | |
S240 | X | X | X | X | X | X | X | |
LT150, LT160, LT180, LT190, LTR180 | X | X | X | X | X | |||
LX280, LX280AWS, LX289 | X | X | X | X | X | |||
X300, X300R, X304, X310, X320, X324, X340, X360, X330, X350, X350R, X354, X370, X380, X384, X390, X394 | X | X | X | X | X | X | X | |
SST15, SST16, SST18 | X | X | X | |||||
G110 | X | X | X | X | X | X | ||
GT235, GT245 | X | X | X | X | X | X | ||
GX255, GX335, GX345, GX355 | X | X | X | X | X | X | ||
X500, X520, X530, X534, X540 X570, X580, X584, X590 | X | X | X | X | X | X | X | |
X465, X475, X485, X495, X575, X585, X595 | X | X | X | X | X | X | X | X |
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758 | X | X | X | X | X | X | X | X |
For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:
Tractor | Additional weight |
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180 | Two 30-lb (14-kg) wheel weights, front Two 42-lb (19-kg) suitcase weights, rear |
S240 | Two 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear |
LT150, LT160, LT180, LT190, LTR180 | Two 34-lb (15-kg) wheel weights, front Two 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190) |
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394 | Two 34-lb (15-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, rear |
SST15, SST16, SST18 | One 88-lb (40-kg) weight kit, front Three 40-lb (18-kg) weights, rear |
G100 | Two 50-lb (23-kg) wheel weights, rear Two 42-lb (19-kg) suitcase weights, rear |
G110 | Two 50-lb (23-kg) plastic shell rear wheel weights |
GT235, GT245 | Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear |
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590 | Two 30-lb (14-kg) wheel weights, front Four 42-lb (19-kg) suitcase weights, front Four 42-lb (19-kg) suitcase weights, rear Four 50-lb (23-kg) wheel weights, rear Two 50-lb (23-kg) wheel plastic shell weights, rear |
X465, X475, X485, X495, X575, X585, X595 | Four 42-lb (19-kg) suitcase weights, front Two 70-lb (32-kg) wheel cast-iron starter weights, rear Four 50-lb (23-kg) cast-iron wheel weights, rear Two 50-lb (23-kg) plastic shell wheel weights, rear Six 42-lb (19-kg) suitcase weights, rear |
Ordering information
Please contact a local John Deere dealer for availability and pricing information.
18 Steel Utility Cart
Order number: LPHDC18JD
Oilite is a trademark of Beemer Precision, Incorporated.
1-7/8-in. (48-mm) hitch ball attaches to drawbar or rear hitch to allow towing. 0.75-in. (19-mm) diameter post thread is provided.
The hitch ball is available through Parts.
Fits John Deere lawn and garden tow behind attachments.
Customers, please contact your local John Deere dealer for availability and pricing information.
Magnetic hitch pin
Order number: LP63768
Home maintenance kits are a handy and convenient way for dealers to supply a customer with the maintenance-interval parts as specified in their operator's manual.
The LG265 home maintenance kit includes the following:
Quantity | Description |
1 | Engine oil filter |
2 | Engine oil quart |
1 | Fuel filter |
1 | Air filter element |
1 | Air filter element foam |
2 | Spark plug |
Features and benefits:
*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s web site for additional information.
Specifications
Capacity | 42 bu (1500 L), 53 cu ft (1.5 m3) |
Engine | 205 cc, 9.00 lb-ft* gross torque |
Impeller | Welded steel |
Tractor compatibility** | X500 Multi-Terrain and X700 Series Tractors |
Mower compatibility | 48-, 54-, 54- HC, 60- 7-Iron, 60- HC, and 62-in. (122-, 137-, 137-, 152-, 152-, and 157-cm) John Deere Mower Decks |
*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s Web site for additional information.
**For proper braking and operation, the loaded weight of the collection system should never
exceed the weight of the tractor, or other towing unit, plus the operator. Additional ballast on
the tractor, or other towing unit, may be needed to meet this requirement.
Please contact your local John Deere dealer for availability and pricing information.
MC542 Material Collection System, boot and hose kits
Order number:
LP22834 - MC542 Material Collection System
LP23080 - Boot kit for 48-in. (122-cm) Mower Deck (48X)
LP65063 - Boot kit for 48-in. (122-cm) Mower Deck (48A)
LP65064 - Boot kit for 54-in. (137-cm) Mower Deck (54A)
LP23081 - Boot kit for 54-in. (137-cm) Mower Deck (54X)
LP44079 - Boot kit for 54-in. (137-cm) Mower Deck (54 HC)
LP23082 - Boot kit for 60-in. (152-cm) Mower Deck (60 HC and 7-Iron™ 60D)
LP23083 - Boot kit for 62-in. (157-cm) Mower Deck
LP39450 - MC542 Hose kit
The Power Flow chute is required, along with the high-performance Power Flow blower, to use the 3-bag Power Flow MCS. The chute includes a convenient handle and a fill indicator that tells the operator when the bags are getting full.
One chute works with several tractor applications. Trim lines on the chute are referenced in the instructions so the chute can be cut to the proper length for the tractor/mower application.
The 3-bag hopper installs to the tractor with the Click-N-Go™ mounting system:
NOTE: The chute can be used with 48C/48X, 54C/54X, 60-in. (152-cm) 7-Iron™, 62C/62X, 62D, 54 HC, and 60 HC Mowers.
The Power Flow chute is required, along with the high-performance Power Flow blower, to use the 2-bag Power Flow material collection system. The chute includes a convenient handle and a fill indicator that tells the operator when the bags are getting full.
One chute works with several vehicle applications. Trim lines on the chute are referenced in the instructions so the chute can be cut to the proper length for the vehicle/mower application.
The Power Flow chute is required, along with the high-performance Power Flow blower, to use the MC519 Cart MCS.
The 14-bu (493-L), 3-bag Power Flow MCS increases the versatility of the X500 Multi-Terrain Tractors and the GT and GX Series garden tractors equipped with a 48-in. (122-cm) or 54-in. (137-cm) Convertible or Edge™ Xtra mower and C-Series high-performance Power Flow blower.
The large 14-bu (493-L) capacity means the operator can collect a large area of grass or leaves before needing to stop to empty the bags.
The 7-bu (247-L) hopper provides an efficient means of collecting grass clippings and leaves using either the cut-and-throw rear bagger or the Power Flow material collection system (MCS):
The hopper design provides modern styling, great bagging performance, cleaner operation, and easy-to-empty bags.
The 7-bu (247-L) MCS features:
A loose-knit bag is available as an option for use with 7-bu (247-L) cut-n-throw rear baggers and Power Flow™ baggers:
The MC519 is compatible with Select Series™ X320, X324, X340, X360, X380, X384, X390, X394, X500 Series Multi-Terrain, X700 Series Tractors, GT200, GX300, X400, and X500 Heavy-Duty Garden Tractors, and 110 through 455 Garden Tractors.
NOTE: MC519 is not compatible with D100 Series, LA100 Series, L100 Series, 100 Series, or Select Series model X300, X304, X310, X330, X350, X354, X370 Tractors, LT, LX, or SST Lawn Tractors, or G100 or G110 Garden Tractors.
The MC519 is designed to provide the versatility of two products in one - a utility cart or a material collector.
Utility cart:
Collector:
Potential customers include homeowners, commercial operators, nurseries, and estates.
The MC519 hitch can be connected to the tractor without tools in about one minute.
In combination with non-jackknifing caster wheels, this semi-rigid hitch makes it easy to maneuver the cart/collector.
An easy-to-reach handle allows dumping the cart/collector from the tractor seat.
For dumping extra-heavy loads, the operator can use the hand grip on the front of the box.
A standard equipment cover can be installed in a matter of seconds to convert the utility cart to a collector:
The MC519 has the durability to handle homeowner or commercial applications:
When equipped with the optional blower and discharge chute (ordered separately), the MC519 becomes a material collection system.
The blower housing material is high-density polyethylene and the fan material is ultra-high molecular weight polyethylene:
Specifications
Capacity | |
Collector | |
Volume | 19 bu (670 L) or 23 cu ft (0.67 m3) |
Load | 500 lb (226.8 kg) |
Cart | |
Volume | 7.5 cu ft (0.21 m3) heaped; 6 cu ft (0.17 m3) struck |
Load | 500 lb (226.8 kg) |
Box dimensions | |
Width | 42 in. (107 cm) |
Length | 30 in. (76 cm) |
Depth | 8 in. (20 cm) |
Overall dimensions, including hitch | |
Width | 45.5 in. (116 cm) |
Length | 51 in. (129.5 cm) |
Depth | 44 in. (112 cm) |
Clearance | 10 in. (25 cm) |
Dump angle | 50 degrees |
Weight, shipping (with carton) | 176 lb (80 kg) |
Weight, net | |
Cart only | 119 lb (54 kg) |
Cover only | 26 lb (12 kg) |
Hitch only | 7.7 lb (3.47 kg) |
Power Flow™ dimensions | |
Fan diameter | 13 in. (334 mm) |
Fan width | 2.75 in. (70 mm), 3.75 in. (95 mm) for C Series Blowers |
Fan blades | 4, 5 for C Series Blowers |
Fan speed | 3400 (will vary with mower width) |
Tires | 4.10x3.50 4PR |
Bearings | |
Wheel | Iron/Oilite™ with grease fittings |
Caster | Roller ball with urethane seals and grease fittings |
Box material | 18-gauge, 0.05-in. (1.2-mm) steel |
Cover material | 14-oz (0.4-kg) black vinyl-coated nylon top, front, and upper side flaps 9.5-oz (0.27-kg) black polyester knitted cloth lower sides 0.397-sq yd (0.33-m2) knitted polyester netting |
Oilite is a trademark of Beemer Precision Incorporated.
The MC519 Cart is compatible with the following tractors with 48A and 54A Accel Deep™ Decks, 38, 46, 48, 48C Convertible, 48 Edge™ Xtra Deck, 50-, 54-, 54C Convertible, 54 Edge Xtra Deck, 60, 60-in. (152-cm) 7-Iron™, 62C Convertible, 62 Edge Xtra Deck, or 54-in. (137-cm), or 60-in. (152-cm) High-Capacity (HC) mowers:
Requirements and/or recommendations:
1. Four 200 lb (91 kg) cast-iron rear wheel weights are recommended for ballast on GT242, GT262, GT275, GT225, GT235, GT245, 240, 245, 260, 265, 285, 320, 325, 335, 345, 355D, GX325, GX335, GX345, GX355, X500, X520, X534, and X540 Tractors when operating on slopes. Select Series X320, X324, X340, X360, X380, X384, X390, and X394 Tractors may need ballast to increase traction, stability, or steering, especially when operating on hillsides or if carrying heavier materials in the MC519 Cart.
2. 420 and 430 Tractors require one AM118915 60-in. (152-cm) Power Flow installation kit for mounting 60-in. (152-cm) Power Flow blower.
3. 316, 318, 322, 330, 332, 420, 430 require black hitch mounting bracket M115521.
Required on MC519 (S/N 045001 - ) to mount on the following Tractors:
This bracket was included in older MC519's but was eliminated when the 425, 445 and 455 Tractors hitch design was changed and the bracket was no longer required for hookup.
4. GT, 300 and GX 48C Mowers built before April 2002 may need 0.5-in. (13-mm) hole drilled in mower wheel bracket for installing BM20667 or BM21495 48C HP Blower. See Service Information Bulletin 02-11-45-7 for detailed instructions.
5. GT, 300 and GX 48C Mowers built after April 2002 may need slot added to mower wheel bracket for installing BM19439 and BM20523 QT Blower. See Service Information Bulletin 02-11-45-7 for detailed instructions.
6. X400/X500 HDGT's and X700 Ultimate Tractors require LP52039 Adaptor Kit for MC519 Cart, available from Order Zone.
7. X400/X500 HDGT's and X700 Ultimate Tractors with a 48C/48X Mower require BM20976 or BM22798 48 HP Adapter Kit to install BM20667 48C High-Performance Power Flow Blower Assembly to accommodate this mower's rotateable wheels:
8. The following older 425, 445, and 455 Tractors without a 3-point hitch also require black hitch mounting bracket M115521:
9. BM20668 54C and BM20669 62C HP Power Flow Blowers require one AM133822 Mower Wheel Adjustment Pin for installation on 2004 and later 54C or 62C Mowers.
NOTE: In order to be used as a material collection system, an optional Power Flow blower and discharge chute must be ordered in addition to the LP49228 MC519 Material Collection System.
Customers, please contact a local John Deere dealer for availability and pricing information.
MC519 Material Collection System
Order number: LP49228
Features and benefits:
*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s web site for additional information.
Specifications
Capacity | 42 bu (1500 L), 53 cu ft (1.5 m3) |
Engine | 205 cc, 9.00 lb-ft* gross torque |
Impeller | Welded steel |
Tractor compatibility** | X500 Multi-Terrain and X700 Series Tractors |
Mower compatibility | 48-, 54-, 54- HC, 60- 7-Iron, 60- HC, and 62-in. (122-, 137-, 137-, 152-, 152-, and 157-cm) John Deere Mower Decks |
*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s Web site for additional information.
**For proper braking and operation, the loaded weight of the collection system should never
exceed the weight of the tractor, or other towing unit, plus the operator. Additional ballast on
the tractor, or other towing unit, may be needed to meet this requirement.
Please contact your local John Deere dealer for availability and pricing information.
MC542 Material Collection System, boot and hose kits
Order number:
LP22834 - MC542 Material Collection System
LP23080 - Boot kit for 48-in. (122-cm) Mower Deck (48X)
LP65063 - Boot kit for 48-in. (122-cm) Mower Deck (48A)
LP65064 - Boot kit for 54-in. (137-cm) Mower Deck (54A)
LP23081 - Boot kit for 54-in. (137-cm) Mower Deck (54X)
LP44079 - Boot kit for 54-in. (137-cm) Mower Deck (54 HC)
LP23082 - Boot kit for 60-in. (152-cm) Mower Deck (60 HC and 7-Iron™ 60D)
LP23083 - Boot kit for 62-in. (157-cm) Mower Deck
LP39450 - MC542 Hose kit
The MCS 14 attachment is designed to provide dump-from-seat grass collection and expulsion for all John Deere 3-bag material collection systems (MCS) on the X500 and X700 Series Tractors. The MCS attachment eliminates the need to get off of the tractor and empty the bags. As a result, it will increase both efficiency and cleanliness in the mowing process.
The aluminum body is light weight and easy to handle. A conveniently located lever and smooth release and latching system are easily accessed from the tractor seat. Because it is engineered specifically for the John Deere material collection system, installation is a breeze with simple hand tools.
Features:
Benefits:
NOTE: Fits John Deere 3-bag material collection systems on X500 and X700 Series Tractors.
Please contact your local John Deere dealer for availability and pricing information.
MCS 14 attachment
Order number: LP47170
The MCS 8 attachment is designed to provide dump from the seat grass collection/expulsion for all John Deere X500 and X700 Series tractors equipped with the 2-bag material collection system (MCS). The MCS attachment eliminates the need to get off of the tractor and empty the bags. As a result, it will increase both efficiency and cleanliness in the mowing process.
The aluminum body is lightweight and easy to handle. Conveniently located hand lever and smooth release and latching system are easily accessed from the tractor seat. Because it is engineered specifically for the John Deere MCS, installation is a breeze with simple hand tools.
Features:
Benefits:
NOTE: Fits All John Deere X500 and X700 Series 2-bag material collection systems. Not compatible with EZtrak™ Zero-Turn Mowers.
Please contact your local John Deere dealer for availability and pricing information.
MCS 8 attachment
Order number: LP47169
The high-performance (HP) Power Flow blower assembly for the 48-in. (122-cm) Accel Deep™ Mower is used with the hopper and chute to provide a very effective material collection system. A hopper and chute must be ordered separately to complete this material collection system.
The high-performance (HP) Power Flow blower assembly for the 54-in. (137-cm) Accel Deep™ Mower is used with the hopper and chute to provide a very effective material collection system. A hopper and chute must be ordered separately to complete this material collection system.
The 40-in. (102-cm) Tractor Shovel expands the usefulness of any John Deere Select SeriesTM X300 or X500 Multi-Terrain Tractor by allowing it to pick up and move material. It utilizes a high-capacity electric actuator that provides lift, lower, dump, and down force functions. No front blade is required.
The tractor shovel takes the back-breaking labor out of jobs like moving mulch, spreading gravel, ground grading, and more. It installs using the tractor's existing frame holes. After initial installation, it can be removed or installed without tools.
The innovative opening design of the tractor shovel, combined with the lift height, assures complete emptying of material. The tractor shovel can also be used for scraping and grading by locking the shovel in the raised position.
Tractor recommendations and requirements:
Key features:
Compatibility:
The unique design of the 40-in. (102-cm) Tractor Shovel allows an operator who has a Select Series™ X300 Series (including X300R and X350R) or X500 Series Multi-Terrain Tractor to use the tractor shovel for lifting and moving material as well as for typical blade functions (without blade angling), such as blading, leveling, and scraping:
The tractor shovel is operated from the tractor seat with the use of a control rod and an electric switch.
An electric actuator provides power to raise, lower, and empty the shovel.
To raise or lower the tractor shovel, use the electric switch on the tractor shovel panel.
Depress the bottom of the switch to raise the shovel and depress the top of the switch to lower the shovel.
To open the shovel for emptying, raise it completely and then pull the control rod to the yellow area of the rod and press the upper end of the electric switch.
To close the shovel, press the lower end of the electric switch until the control rod releases to the black area of the rod.
To use the tractor shovel for blading, use the handle on the right side of the shovel to raise it and then use the locking lever to lock it in the raised position.
Specifications
Length of tractor shovel | 40 in. (101.6 cm) |
Depth of tractor shovel | 11 in. (27.9 cm) |
Capacity | 1.7 ft3 (48 L) |
Cutting blade material | 0.250-in. (6.4-mm) hardened steel |
Material thickness, shovel | 0.125 in. (3.2 mm) |
Load capacity | 150 lb (68 kg), evenly distributed |
Lift height | 4 in. to 6 in. (10.2 cm to 15.2 cm), depending on the tractor model |
Shipping weight | 110 lb (50 kg) |
Warranty | One-year limited warranty on parts |
The 40-in. (102-cm) Tractor Shovel is compatible with the following tractors:
Requirements and/or recommendations:
Please contact your local John Deere dealer for availability and pricing information.
40-in. (102-cm) Tractor Shovel
Order number: LP63767
This fully automatic 1.5-amp battery charger and maintainer safely charges lawn and garden, RV, deep-cycle, and most batteries that require long storage periods. It is particularly useful during winter months when the vehicle is not being used regularly, to ensure the battery stays charged:
Includes a choice of battery connection methods:
Transporting mulch, plants or debris is easier with the double bucket holder. Just attach the holder bracket to the rear of any Select Series™ X300, X500 Series Multi-Terrain, or X700 Ultimate™ Series Tractor. It is designed to carry up to 70 lb (32 kg) of material.
For use with standard 5-gal. (19-L) buckets - ordered separately.
Please contact your local John Deere dealer for availability and pricing information.
Bucket holder (double)
Order number: LPJD301
Bucket (5-gal.)
Order number: LPJD400 (2 required)
Transporting mulch, plants, or debris is easier with the double bucket holder. Just attach the holder bracket to the rear of any Select Series™ X300, X500 Series Multi-Terrain, or X700 Series Tractor. It is designed to carry up to 70 lb (32 kg) of material for transporting mulch, plants, yard waste, or for adding ballast.
For use with the included John Deere 5-gal. (19-L) buckets.
NOTE: May not fit all tractor models with a weather enclosure or cab installed.
Please contact your local John Deere dealer for availability and pricing information.
Bucket holder (double) with buckets
Order number: LPJD301W
This black 5-gal. (19-L) bucket perfectly complements the CargO Mount™ single and double bucket holders. It is made of sturdy black plastic.
Please contact your local John Deere dealer for availability and pricing information.
Bucket - 5 gal. (19-L)
Order number: LPJD400
John Deere Fuel-Protect gasoline stabilizer is a unique formula developed to ensure optimum performance and protection year-round:
Always use fuel stabilizer in gasoline.
Fuel sitting in gas tanks or gas containers for more than 30 days begins to degrade. Also, blended fuels and water in gasoline can form acids that corrode fuel-system components. Protect the investment - use John Deere fuel stabilizer with corrosion preventers and prevent hard starting, surging, lack of power, poor idle, flooding, and will not run or stay running conditions caused by poor-quality fuel. Ask a local John Deere dealer or visit JDParts.
Helpful tips:
Please refer to the operator’s manual for additional recommendations and warranty information.
Fuel related issues are not considered a warrantable condition as there is no defect in the materials or workmanship of the machine.
For more information on fuel, visit John Deere Groundscare.
The John Deere MowerPlus smart connector wirelessly links a Select Series X300 or X500 Tractor to the MowerPlus app on a mobile device:
Tractor features available for viewing on the MowerPlus app include:
The operator is able to visit their device’s app store to see new app features as they are added.
Since the smart connector communicates instrument cluster information, future app releases will be able to provide additional operating recommendations and notifications.
One end of the wiring harness plugs into the back of a Select Series X300 or X500 Tractor instrument cluster. The other ends plug into the smart connector and the tractor's wiring harness.
MowerPlus smart connector (BUC10537) is for model year 2016 and later Select Series X300 and X500 Tractors.
Requires the MowerPlus app on a mobile device to use. The John Deere MowerPlus app can be found in the mobile device’s app store. This operating system version is required:
NOTE: The John Deere MowerPlus app is only available in the English language, and it is not available in all countries. Find operating system version availability in the mobile device’s app store.
Bluetooth is a trademark of Bluetooth SIG, Inc. Android is a trademark of Google LLC. iOS is a trademark of Cisco Technology, Inc. used under license by Apple Inc.
M152726 is an approved alternative to M143520, standard side-discharge blade. M152726 improves cut-quality performance in certain grass conditions. It will increase the amount of lift or suction under the deck. It will be most beneficial for customers who are experiencing cut quality issues with the standard blade, especially in limp grass, typical in early spring and late fall. The blade will improve side-discharge performance, but a potential downside is increased blow-out in dry conditions.
M152726 is an approved alternative to M143520, standard side-discharge blade. M152726 improves cut-quality performance in certain grass conditions. It will increase the amount of lift or suction under the deck. It will be most beneficial for customers who are experiencing cut quality issues with the standard blade, especially in limp grass, typical in early spring and late fall. The blade will improve side-discharge performance, but a potential downside is increased blow-out in dry conditions.
M152726 is an approved alternative to M143520, standard side-discharge blade. M152726 improves cut-quality performance in certain grass conditions. It will increase the amount of lift or suction under the deck. It will be most beneficial for customers who are experiencing cut quality issues with the standard blade, especially in limp grass, typical in early spring and late fall. The blade will improve side-discharge performance, but a potential downside is increased blow-out in dry conditions.
The BM26238 dry-condition kit, 48A is available for 48A Accel Deep Mower Decks used on S240 Tractors, model year 2016 and later X300 and X500 Select Series™ Tractors and Residential ZTrak™ Mowers. The 48A dry-condition kit will also work with any X700 Signature Series Tractor (model year 2013 and later) that is equipped with a 48A Mower Deck.
The dry-condition kit will reduce the amount of blowout around the mower deck when side discharging, mulching, or bagging in dry grass and leaf conditions. For optimum mowing performance in lush-grass conditions, the dry-condition kit baffles may be removed.
The BM26239 dry-condition kit, 54A is available for 54A Accel Deep Mower Decks used on model year 2016 and later X300 and X500 Select Series™ Tractors and Residential ZTrak™ Mowers.
The dry-condition kit will reduce the amount of blowout around the mower deck when side discharging, mulching, or bagging in dry grass and leaf conditions. For optimum mowing performance in lush-grass conditions, the dry-condition kit baffles may be removed.
Compatible with the following:
Customers, please contact your local John Deere dealer for availability and pricing information.
48A or 54A - 48-in. (122-cm) and 54-in. (137-cm) grass groomer
Order number: LP63761
Leveling gauge allows quick and accurate mower deck leveling and cutting height adjustment.
Can be used for:
The MulchControl attachment for the 48A Mower Deck makes mulching more practical for many mowing situations because it not only does an excellent job of mulching but it also allows the mower to be easily converted for times when it is more desirable to side discharge or collect the lawn material. Advantages of mulching grass clippings include:
MulchControl is an innovative, simple design that is easy to use and maintain:
MulchControl is well-suited to the following mowing situations:
MulchControl puts the operator in control of the clippings. The operator can have all the benefits of mulching with the ability to easily change to side discharge or bagging when needed.
While in the side-discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side-discharge mode is essentially a partial-mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:
The 48-in. (122-cm) electric one-touch MulchControl attachment enhances versatility and productivity. A mower deck equipped with electric one-touch MulchControl not only does an excellent job of mowing and mulching, but it can also be quickly converted to side discharge or mulch mode with the touch of a switch:
A tractor equipped with the electric one-touch MulchControl attachment delivers unprecedented levels of productivity and versatility. A convenient, dash-mounted switch provides operators the ability to change between side discharging and mulching. A heavy-duty baffle opens and closes easily with the touch of the dash-mounted switch.
A dependable electric actuator is used to close and open the discharge baffle. The mower deck can easily be converted from side discharge mode to mulch mode or vice versa in a few seconds by activating the switch.
MulchControl is an innovative, simple design that is easy to use and maintain:
MulchControl is well suited to the following mowing situations:
MulchControl puts the operator in control of the clippings. The operator can have all the benefits of mulching with the ability to easily change to side discharging or bagging when desired.
With electric one-touch MulchControl, operators can convert between modes without interrupting the mowing process, making it practical to change between modes as conditions require:
Advantages of MulchControl include:
While in the side discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side discharge mode is essentially a partial mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:
This electric one-touch MulchControl attachment is field installed and compatible with any 48A Mower installed on an X300 or X500 Select Series Tractor.
NOTE: Model year 2016-2017 X300 and X500 Series Tractors (X300 serial number 10,001-50,000 and X500 serial number 110,001-130,000) require replacing the tractor wiring harness and dash panel to use an electric MulchControl attachment.
The MulchControl attachment for the 54A Mower Deck makes mulching more practical for many mowing situations because it not only does an excellent job of mulching but it also allows the mower to be easily converted for times when it is more desirable to side discharge or collect the lawn material. Advantages of mulching grass clippings include:
MulchControl is an innovative, simple design that is easy to use and maintain:
MulchControl is well-suited to the following mowing situations:
MulchControl puts the operator in control of the clippings. The operator can have all the benefits of mulching with the ability to easily change to side discharging or bagging when needed.
While in the side-discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side-discharge mode is essentially a partial-mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:
The 54-in. (137-cm) electric one-touch MulchControl attachment enhances versatility and productivity. A mower deck equipped with electric one-touch MulchControl not only does an excellent job of mowing and mulching, but it can also be quickly converted to side discharge or mulch mode with the touch of a switch:
A tractor equipped with the electric one-touch MulchControl attachment delivers unprecedented levels of productivity and versatility. A convenient, dash-mounted switch provides operators the ability to change between side discharging and mulching. A heavy-duty baffle opens and closes easily with the touch of the dash-mounted switch.
A dependable electric actuator is used to close and open the mulching baffle. The mower deck can easily be converted from side discharge mode to mulch mode or vice versa in a few seconds by activating the switch.
MulchControl is an innovative, simple design that is easy to use and maintain:
MulchControl is well suited to the following mowing situations:
MulchControl puts the operator in control of the clippings. The operator can have all the benefits of mulching with the ability to easily change to side discharging or bagging when desired.
With electric one-touch MulchControl, operators can convert between modes without interrupting the mowing process, making it practical to change between modes as conditions require:
Advantages of MulchControl include:
While in the side discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side discharge mode is essentially a partial mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:
This electric one-touch MulchControl attachment is field installed and compatible with a 54A Mower installed on an X300 or X500 Select Series Tractor.
NOTE: Model year 2016-2017 X300 and X500 Series Tractors (X300 serial number 10,001-50,000 and X500 serial number 110,001-130,000) require replacing the tractor wiring harness and dash panel to use an electric MulchControl attachment.
The brush guard adds a distinctive appearance to the tractor and protects the front of the tractor from damage.
By removing one spring clip and pin, the brush guard may be lowered to permit opening the hood.
Cover provides heavy-duty protection for Select Series™ X300, X500, and X700 Tractors.
Features include:
Customers, please contact your local John Deere dealer for availability and pricing information.
Protective cover (large deluxe)
Order number: LP93647
Features include:
Cover provides all-season protection for 100 Series, S240 and Select Series™ X300 Series Tractors.
Customers, please contact your local John Deere dealer for availability and pricing information.
Protective cover (standard)
Order number: LP93917
The box scraper is perfect for light grading or leveling of dirt, sand, gravel, etc. It can be reversed for backfilling or pushing snow.
Description: Sleeve Hitch Box Scraper
Size/Capacity: 38 in. (96.5 cm)
Blade: 0.19-in. (5-mm) carbon-steel construction
Frame: Center-mounted square-channel steel
Adjustments:
Weight bracket: Included
Fit-up: Easy hook-up to any sleeve hitch or integral hitch (ordered separately)
Warranty: One year limited
Please contact your local John Deere dealer for availability and pricing information.
38-in. (96.5-cm) Box Scraper - Sleeve Hitch
Order number: LPBS38
The Rear Blade is just the right size to handle many grading or backfilling tasks. It can be reversed for backfilling or pushing snow.
Description: Sleeve Hitch Rear Blade
Size/Capacity: 42 in. (107 cm)
Blade: Heavy-duty carbon-steel construction
Frame: Center-mounted, square-channel steel frame
Adjustments: Angles and locks 30 degrees in either direction or rotates 180 degrees for pushing instead of pulling
Fit-up: Easy hook-up to any sleeve hitch or integral hitch (ordered separately)
Warranty: One year limited
Please contact your local John Deere dealer for availability and pricing information.
42-in. (107-cm) Rear Blade - Sleeve Hitch
Order number: LPBB56
The cultivator removes weeds and loosens soil between newly planted rows to give plants every opportunity to grow tall and strong.
Description: Cultivator - Sleeve Hitch
Size/Capacity: Adjustable 18 in. to 40 in. (45.7 cm to 101.6 cm)
Frame/Weights: 0.25-in. (0.64-cm) angle-steel frame, J-bolt provided for adding weight (i.e. concrete block)
Shanks: Seven 12-in. (30.5-cm) rigid shanks, 0.5-in. (13-mm) thick, solid steel
Adjustments: Adjustable depth-control skids provided
Fit-up: Easy hook-up to any sleeve hitch or integral hitch (ordered separately)
Warranty: One year limited
Please contact your local John Deere dealer for availability and pricing information.
Cultivator - Sleeve Hitch
Order number: LPCC55
The disk harrow can get a garden ready for planting quickly and easily. It breaks up chunky, plowed ground and prepares seedbeds with uniform, pulverized soil. Disk angles and spacing can be adjusted according to conditions. Add extra weight to the heavy steel tray for tough soil conditions. Hitch is provided so two disk harrows can be coupled together for a heavier, tandem unit.
Description: Sleeve Hitch Disk Harrow
Size/Capacity: Adjustable 29 in. to 39 in. (73.7 cm to 99.1 cm)
Frame: 11-gauge, 0.12-in. (3.0-mm) tray, 0.375-in. x 2-in. (9.5-mm x 51-mm) frame bar
Discs: Eight 11-in. (28-cm) heat-treated disk blades, 13-gauge, 0.09-in. (2.3-mm) steel
Fittings: Grease fittings on disk hangers
Adjustments: Choice of disk angles: 10, 15, or 20 degrees
Fit-up: Easy hook-up to any sleeve hitch or integral hitch (ordered separately)
Warranty: One year limited
Please contact your local John Deere dealer for availability and pricing information.
Disk Harrow - Sleeve Hitch
Order number: LPDD55
Gardens can be plowed quickly and easily with this all-time favorite plow. A rolling Coulter Blade cuts through the sod. The plow digs the furrow while the moldboard gently turns under old vegetation to make way for new planting.
Description: Sleeve Hitch Moldboard Plow
Size/Capacity: 10-in. (25.4-cm) width of cut
Plow Share: 0.25-in. (0.64-cm) solid steel
Coulter: 13-ga, 0.09-in. (2.3-mm) steel coulter kit included
Adjustments: No tools required to make depth adjustments
Fit-up: Easy hook-up to any sleeve hitch or integral hitch (ordered separately)
Warranty: One year limited
Please contact your local John Deere dealer for availability and pricing information.
Moldboard Plow - Sleeve Hitch
Order number: LPPP510
The integral hitch permits the use of certain rear-mounted equipment, such as a cultivator, disk harrow, plow, or box scraper/blade attachment.
Key features include:
Please contact your local John Deere dealer for availability and pricing information.
Integral hitch
Order number: LP31357
The integral hitch permits the use of certain rear-mounted equipment, such as a cultivator, disk harrow, plow, or box scraper/blade attachment.
Key features include:
Please contact your local John Deere dealer for availability and pricing information.
Power integral hitch
Order number: LP66661
Armrests increase operator support and comfort, thus reducing fatigue and improving productivity, especially when mowing for extended periods of time. Armrests are made with a sewn vinyl cover stretched over foam and are adjustable to suit the operator.
This armrest kit is designed for the 21-in. (53.3-cm) professional two-piece seat shipped on model year 2013-2018 (serial number 010,001-070,000) X700 Signature Series Tractors and is optional for X500 Multi-Terrain Tractors.
Armrests increase operator support and comfort, thus reducing fatigue and improving productivity, especially when mowing for extended periods of time. Armrests are adjustable to suite the operator.
This armrest kit is designed for model year 2011 and later X534 and X540 (SN 060001) and all X590 Multi-Terrain Tractors equipped with the 21-in. (53.3-cm) high-back seat.
The 21-in. (53.3-cm) professional two-piece seat, four-bar suspension, and slide shipped on Signature Series X700 Tractors is available as an upgrade seat and suspension for all X500 Multi-Terrain Tractors (model year 2006-). Key selling features for this seat include:
Armrests increase operator support and comfort, thus reducing fatigue and improving productivity, especially when mowing for extended periods of time. Armrests are adjustable to suit the operator. This armrest attachment is designed for the 21-in. (53.3-cm) professional two-piece seat.
BM25346 21-in. (53.3-cm) professional two-piece seat, four-bar suspension, and slide is a field-installed attachment and compatible as follows:
Spark arrester is available to meet the law in the State of California requiring use of a spark arresting muffler under certain conditions.
Applies in other states and Canada when needed to comply with local ordinances or customer requests.
NOTE: This law basically requires that purchasers of certain products be given written notice that it is illegal to use such machines on forest-covered, brush-covered, or grass-covered land (except watered lawns) without a spark arrester. For further information on this law, consult No. 4442.5 of the California Public Resources Code.
Features and benefits:
Specifications
Item number | LP22861 |
Tank capacity | 25 gal. (95 L) |
Boom | 60-in. (152.4-cm) boom, 90-in. (228.6-cm) spray |
Spray wand reach | 30 ft (9.1 m) |
Hose length | 19 ft (8 m) |
Shipping weight | 35 lb (16 kg) |
Warranty | 2-year consumer warranty |
Please contact your local John Deere dealer for availability and pricing information.
25-gal. (95-L) Mounted Sprayer for X300 and X500 Tractors
Order number: LP22861
SHURflo is a trademark of SHURflo, LLC.
Viton is a trademark DuPont Performance Elastomers.
The 45-gal. (170-L) HP Tow-Behind Sprayer offers the ultimate in performance and versatility. With its large-capacity, high-volume electric pump, and premium pistol-grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. It is the perfect match for the operator who wants extreme performance.
The heavy-duty frame rolls smoothly on 15x6 tires that minimize ground compaction and have a low profile, which maintains a low center of gravity for excellent stability. Cover ground quickly with flexible boom options: a 12.5-ft (3.8-m) precision folding boom, 24-ft (7.3-m) boomless, or no boom at all (boom sold separately).
The HP 12.5-ft (3.8-m) precision boom (LP22885) is compatible with the 45-gal. (170-L) HP Tow-Behind Sprayer. The folding boom is made to cover ground quickly and thoroughly with five precision spray tips, TeeJet nozzle bodies, and commercial-grade diaphragm check valves. The outer tips offer versatility with built-in shut-offs to allow an adjustable 7.5-, 10-, or 12.5-ft (2.3-, 3.05-, or 3.8-m) spray swath.
The 24-ft (7.3-m) HP boomless spray nozzles (LP22884) are compatible with the 45-gal. (170-L) HP Tow-Behind Sprayer. The boom is perfect for covering ground quickly and thoroughly with a 24-ft (7.3-m) spray swath. It is ideal for uneven terrain or where precision spray application is not necessary.
Please contact a local John Deere dealer for availability and pricing information.
45-gal. (170-L) HP Tow-Behind Sprayer
Order number: LP39963
Optional HP 12.5‐ft (3.8‐m) precision boom
Order number: LP22885
Optional HP boomless spray nozzles
Order number: LP22884
TeeJet is a trademark of Spraying Systems Company.
Sprayer comes complete with a boom that sprays 60 in. (152.4 cm) wide. It also has a 12-ft (3.7-m) hose with an adjustable handgun for spot spraying lawns, shrubs, etc.
Features include:
NOTE: Sprayers are compatible with competitive tractors (if equipped with a 12-V battery and charging system).
This sprayer is especially suited for maintaining residential and small commercial properties:
Advantages of using liquid fertilizer over dry fertilizer:
NOTE: Use these sprayers with liquid-base lawn care chemicals only. They are not recommended for wettable powders as no agitating system is provided to prevent particles from separating out.
Customers, please contact your local John Deere dealer for availability and pricing information.
15-gal. (57-L) Tow-Behind Sprayer
Order number: LP19478
Sprayer comes with a wider boom that sprays a 90 in. (228.6 cm) width. A 15-ft (4.6-m) hose and handgun are provided.
Features include:
NOTE: Sprayers are compatible with competitive tractors (if equipped with a 12-V battery and charging system).
This sprayer is especially suited for maintaining residential and small commercial properties.
Advantages of using liquid fertilizer over dry fertilizer:
NOTE: Use this sprayer with liquid-based lawn care chemicals only. It is not recommended for wettable powders as no agitating system is provided to prevent particles from separating out.
Customers, please contact your local John Deere dealer for availability and pricing information.
25-gal. (95-L) Tow-Behind Sprayer
Order number: LP19479
SHURflo is a trademark of SHURflo, LLC.
Features include:
Tow-behind sprayer is equipped with a boom that sprays a wide 120-in. (308.4-cm) width. The 45-gal.(170-L) sprayer is capable of covering more area with less refills:
NOTE: Sprayers are compatible with competitive tractors (if equipped with a 12-V battery and charging system).
This liquid sprayer is especially suited for maintaining residential and small commercial properties:
Advantages of using liquid fertilizer over dry fertilizer:
NOTE: Use this sprayer with liquid-based lawn care chemicals only. It is not recommended for wettable powders as no agitating system is provided to prevent particles from separating out.
SHURflo is a trademark of SHURflo, LLC.
Customers, please contact your local John Deere dealer for availability and pricing information,
45-gal. (170-L) Tow-Behind Sprayer
Order number: LP20485
The 45-gal. (170-L) HP Tow-Behind Sprayer offers the ultimate in performance and versatility. With its large-capacity, high-volume electric pump, and premium pistol-grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. It is the perfect match for the operator who wants extreme performance.
The heavy-duty frame rolls smoothly on 15x6 tires that minimize ground compaction and have a low profile, which maintains a low center of gravity for excellent stability. Cover ground quickly with flexible boom options: a 12.5-ft (3.8-m) precision folding boom, 24-ft (7.3-m) boomless, or no boom at all (boom sold separately).
The HP 12.5-ft (3.8-m) precision boom (LP22885) is compatible with the 45-gal. (170-L) HP Tow-Behind Sprayer. The folding boom is made to cover ground quickly and thoroughly with five precision spray tips, TeeJet nozzle bodies, and commercial-grade diaphragm check valves. The outer tips offer versatility with built-in shut-offs to allow an adjustable 7.5-, 10-, or 12.5-ft (2.3-, 3.05-, or 3.8-m) spray swath.
The 24-ft (7.3-m) HP boomless spray nozzles (LP22884) are compatible with the 45-gal. (170-L) HP Tow-Behind Sprayer. The boom is perfect for covering ground quickly and thoroughly with a 24-ft (7.3-m) spray swath. It is ideal for uneven terrain or where precision spray application is not necessary.
Please contact a local John Deere dealer for availability and pricing information.
45-gal. (170-L) HP Tow-Behind Sprayer
Order number: LP39963
Optional HP 12.5‐ft (3.8‐m) precision boom
Order number: LP22885
Optional HP boomless spray nozzles
Order number: LP22884
TeeJet is a trademark of Spraying Systems Company.
The 45-gal. (170-L) HP Tow-Behind Sprayer offers the ultimate in performance and versatility. With its large-capacity, high-volume electric pump, and premium pistol-grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. It is the perfect match for the operator who wants extreme performance.
The heavy-duty frame rolls smoothly on 15x6 tires that minimize ground compaction and have a low profile, which maintains a low center of gravity for excellent stability. Cover ground quickly with flexible boom options: a 12.5-ft (3.8-m) precision folding boom, 24-ft (7.3-m) boomless, or no boom at all (boom sold separately).
The HP 12.5-ft (3.8-m) precision boom (LP22885) is compatible with the 45-gal. (170-L) HP Tow-Behind Sprayer. The folding boom is made to cover ground quickly and thoroughly with five precision spray tips, TeeJet nozzle bodies, and commercial-grade diaphragm check valves. The outer tips offer versatility with built-in shut-offs to allow an adjustable 7.5-, 10-, or 12.5-ft (2.3-, 3.05-, or 3.8-m) spray swath.
The 24-ft (7.3-m) HP boomless spray nozzles (LP22884) are compatible with the 45-gal. (170-L) HP Tow-Behind Sprayer. The boom is perfect for covering ground quickly and thoroughly with a 24-ft (7.3-m) spray swath. It is ideal for uneven terrain or where precision spray application is not necessary.
Please contact a local John Deere dealer for availability and pricing information.
45-gal. (170-L) HP Tow-Behind Sprayer
Order number: LP39963
Optional HP 12.5‐ft (3.8‐m) precision boom
Order number: LP22885
Optional HP boomless spray nozzles
Order number: LP22884
TeeJet is a trademark of Spraying Systems Company.
The mounted electric broadcast spreader for Select Series and Signature Series Tractors is ideal for medium- to large-size jobs and can be used to apply fertilizer, weed killer, sand, lime, and de-icer:
Key features are as follows:
Please contact your local John Deere dealer for availability and pricing information.
Select Series Electric Spreader
Item number: LP35439
The barrier shield is used to direct product downward (36-in. [914-mm] width), converting the rotary spreader into a drop spreader. Perfect for ice melt and salt spreading, or for targeting specific areas.
Please contact your local John Deere dealer for availability and pricing information.
125-lb electric broadcast spreader barrier shield
Order number: LP23117
John Deere spin spreaders have features and a choice of sizes to satisfy many operators. They are a popular attachment for both homeowner and commercial operators who use them for even distribution of a variety of materials:
All spreaders have rust-resistant stainless-steel or polyethylene hoppers as well as many stainless-steel components to ensure lasting appearance and long, trouble-free operation.
Features include:
Accu-way is a trademark of Spyker Spreaders, Inc.
Hopper screens keep out debris and serve as chunk graters.
A stainless-steel hopper bottom plate/throat opening resists rust and corrosion, which extends the life of the spreader.
Spinners are made of high-impact plastic that will not crack or break.
The Dial-A-Matic rate control lets the operator fine-tune the rate application:
125-lb (57-kg) Pull-Type Spreader | 175-lb (79-kg) Pull-Type Spreader | |
Recommended market | Homeowner | Homeowner |
Type | Tow-behind | Tow-behind |
Bundle number | LP25353 | |
Box capacity | 125 lb (57 kg), 2.5 cu ft (0.07 m3) | 175 lb (79 kg), 3.5 cu ft (0.1 m3) |
Hopper size, in. (cm) | 14.5x25.25x19.75 (36.8x64.1x50.2) | 18.5x27.5x21.5 (47x69.9x54.6) |
No-rust versatility | ||
Hopper | Polyethylene | Polyethylene |
Hopper screen | Aluminum | Aluminum |
Hopper bottom plate | Stainless steel | Stainless steel |
Throat opening, in. (cm) | 0.81x2.75 (2.1x7) | 0.81x2.75 (2.1x7) |
Connecting hardware | Stainless steel | Stainless steel |
Accurate application | ||
Rate control | 80-setting Dial-A-Matic knob | 80-setting Dial-A-Matic knob |
Rate gate | No-stick nylon | No-stick nylon |
Rate gate linkage | Stainless steel | Stainless steel |
Even dispersal | ||
Spinner, in. (cm) | 12 (366) | 12 (366) |
Spread pattern, ft (m) | 10 to 12 (3.1 to 3.7) wide | 10 to 12 (3.1 to 3.7) wide |
Spread pattern equalizer | Accu-way™ | Accu-way |
Spinner shaft | Zinc-plated steel | Zinc-plated steel |
Rotary agitator | Stainless steel | Stainless steel |
Miscellaneous | ||
Frame | Powder-coated gloss enamel, 16 ga, 0.6 in. (1.5 mm) 1.13-in. (2.86-cm) tubular steel | Powder-coated gloss enamel, 16 ga, 0.6 in. (1.5 mm), 1.25-in. (3.2-cm) tubular steel |
Frame width, in. (cm) | 18 (45.7) | 18 (45.7) |
Drive gears | Heavy-duty die-cast metal | Heavy-duty die-cast metal |
Axle | 0.63-in. (15.9-cm) solid steel, zinc plated | 0.63-in. (15.9-cm) solid steel, zinc plated |
Wheels/tires | 13-in. x 5-in. (33-cm x 13-cm) pneumatic | 13-in. x 5-in. (33-cm x 13-cm) pneumatic |
Recommended travel speed | 3.5 mph (5.6 km/h) | 3.5 mph (5.6 km/h) |
Warranty | One-year limited | One-year limited |
Net weight, lb (kg) | 29 (13.2) | 34 (15.4) |
Accu-way is a trademark of Spyker Spreaders, Inc.
Please contact your local John Deere dealer for availability and pricing information.
125-lb Pull-Type Spin Spreader
Order number: LP25353
John Deere spin spreaders have features and a choice of sizes to satisfy many operators. They are a popular attachment for both homeowner and commercial operators who use them for even distribution of a variety of materials:
All spreaders have rust-resistant stainless-steel or polyethylene hoppers as well as many stainless-steel components to ensure lasting appearance and long, trouble-free operation.
Features include:
Hopper screens keep out debris and serve as chunk graters.
A stainless-steel hopper bottom plate/throat opening resists rust and corrosion, which extends the life of the spreader.
Spinners are made of high-impact plastic that will not crack or break.
The Dial-A-Matic rate control lets the operator fine-tune the rate application:
125-lb (57-kg) Pull-Type Spreader | 175-lb (79-kg) Pull-Type Spreader | |
Recommended market | Homeowner | Homeowner |
Type | Tow-behind | Tow-behind |
Bundle number | LP25353 | |
Box capacity | 125 lb (57 kg), 2.5 cu ft (0.07 m3) | 175 lb (79 kg), 3.5 cu ft (0.1 m3) |
Hopper size, in. (cm) | 14.5x25.25x19.75 (36.8x64.1x50.2) | 18.5x27.5x21.5 (47x69.9x54.6) |
No-rust versatility | ||
Hopper | Polyethylene | Polyethylene |
Hopper screen | Aluminum | Aluminum |
Hopper bottom plate | Stainless steel | Stainless steel |
Throat opening, in. (cm) | 0.81x2.75 (2.1x7) | 0.81x2.75 (2.1x7) |
Connecting hardware | Stainless steel | Stainless steel |
Accurate application | ||
Rate control | 80-setting Dial-A-Matic knob | 80-setting Dial-A-Matic knob |
Rate gate | No-stick nylon | No-stick nylon |
Rate gate linkage | Stainless steel | Stainless steel |
Even dispersal | ||
Spinner, in. (cm) | 12 (366) | 12 (366) |
Spread pattern, ft (m) | 10 to 12 (3.1 to 3.7) wide | 10 to 12 (3.1 to 3.7) wide |
Spread pattern equalizer | Accu-way™ | Accu-way |
Spinner shaft | Zinc-plated steel | Zinc-plated steel |
Rotary agitator | Stainless steel | Stainless steel |
Miscellaneous | ||
Frame | Powder-coated gloss enamel, 16 ga, 0.6 in. (1.5 mm) 1.13-in. (2.86-cm) tubular steel | Powder-coated gloss enamel, 16 ga, 0.6 in. (1.5 mm), 1.25-in. (3.2-cm) tubular steel |
Frame width, in. (cm) | 18 (45.7) | 18 (45.7) |
Drive gears | Heavy-duty die-cast metal | Heavy-duty die-cast metal |
Axle | 0.63-in. (15.9-cm) solid steel, zinc plated | 0.63-in. (15.9-cm) solid steel, zinc plated |
Wheels/tires | 13-in. x 5-in. (33-cm x 13-cm) pneumatic | 13-in. x 5-in. (33-cm x 13-cm) pneumatic |
Recommended travel speed | 3.5 mph (5.6 km/h) | 3.5 mph (5.6 km/h) |
Warranty | One-year limited | One-year limited |
Net weight, lb (kg) | 29 (13.2) | 34 (15.4) |
Accu-way is a trademark of Spyker Spreaders, Inc.
Please contact your local John Deere dealer for availability and pricing information.
175-lb Pull-Type Spin Spreader
Order number: LP25354
The 40-in. (102-cm) Aerator Spreader can do two jobs at once. It perforates the soil while the calibrated drop-spreader follows with seed, lime, or fertilizer. It can also be used to just aerate the lawn:
John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.
This implement features legendary John Deere performance and quality.
Specifications
Width | 40 in. (101.6 cm) |
Aerator depth | Up to 2 in. (5.1 cm), two positions |
Spreader capacity | 100 lb (45 kg) |
Tines | |
Number of tips | 132 |
Diameter | 8 in. (20.3 cm) |
Material | Steel |
Lift adjuster | Manual |
Wheels | 4.10/3.5-4, pneumatic |
Drive | Direct |
Weight-tray capacity | 100 lb (45 kg) |
Requirements and/or recommendations: tow-behind equipment
Customers, please contact your local John Deere dealer for availability and pricing information.
40-in. (102-cm) Tow-Behind Aerator Spreader
Order number: LPAS40JD
Broadcasts fertilizer, weed control, grass seed or ice melter products while towing behind a riding lawn tractor. 130-lb (59-kg) polyethylene hopper resists rust and is easier to clean. Spread pattern will go up to 12 ft (31 cm) depending on speed and material. New direct rod control with easy to reach handle opens and closes the material gate. Heat treated steel gears with plastic enclosure are protected from corrosive material. Large knobby tread tires roll easily over turf.
Two-year warranty.
Please contact your local John Deere dealer for availability and pricing information.
130-lb Pull-Type Spin Spreader
Order number: LP39087
This 175-lb (79-kg) pull-type broadcast spreader is designed for homeowner use:
Please contact your local John Deere dealer for availability and pricing information.
175-lb (79-kg) Broadcast Spreader
Order number: LPBS36JD
The sturdy sun shade provides an effective way to keep the sun off of the operator for more comfortable warm-weather operation of the tractor:
The sun shade mounts to the heavy-duty CargO Mount™ system.
The sun shade is compatible with the following:
The 7-bu (247-L) 2-bag hopper or 14-bu (493-L) 3-bag hopper can be installed and used with the sun shade installed. The sun shade installation instructions explain how to install the hoppers with the sun shade.
Please contact your local John Deere dealer for availability and pricing information.
X300/X500 Sun Shade
Order number: BM23054
The thatcher, used on a regular basis, reduces excessive thatch buildup that can be damaging to a lawn's health.
Since it provides more gentle, less aggressive action than a power rake, it can be used as a preventive maintenance tool each time the lawn is mowed.
Please contact a local John Deere dealer for availability and pricing information.
38-in. (97-cm) Front Thatcher
Order number: LP48004
An 8-in. (20-cm) extension is available to provide widths of 46 in. (117 cm) and 54 in. (137 cm) (Add an extension to one end of front thatcher to make it 46-in. [117-cm] wide; add an extension to both ends for a 56-in. [142-cm] width.)
A thatcher mounting frame is required to install the 38-in. (97-cm) front-mounted thatcher on a vehicle.
The 40-in. (102-cm) Thatcherator can be used as a dethatcher or an aerator. It can also be used to prepare an area for seed:
An 8-in. (20-cm) extension is available to provide widths of 48 in. (122 cm) and 56 in. (142 cm) (Add an extension to one end of Thatcherator to make it 48-in. (122-cm) wide and an extension to both ends for a 56-in. (142-cm) width.)
John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.
This implement features legendary John Deere performance and quality.
Specifications
Width | 40 in. (101.6 cm) |
Tines | |
Number | 20, spring-loaded tips |
Diameter | 0.19 in. (0.5 cm) |
Material | Steel |
Weight tray capacity | 100 lb (45 kg) |
Lift adjuster | Three positions |
Wheel | |
Size | 8 in. (20.3 cm) |
Tread | Rib |
Material | Steel |
Optional extension | 8 in. (20.3 cm) |
Requirements and/or recommendations: tow-behind equipment
Customers, please contact your local John Deere dealer for availability and pricing information.
40-in. (102-cm) Tow-Behind Thatcherator
Order number: LPTA40JD
Chains are recommended for extra traction when using attachments such as a snow blower or front blade.
One pair of chains is included in each bundle.
TY15959 tire chains - 20x8-8
NOTE: For LA105, LA115, LA125, D100, D105, D110, D120, D125, E100, E110, and E120 Tractors.
TY16200 tire chains - 20x10-8 (for some models), 20x10-10
NOTE: For LA135 SE, LA145, LA155, S240, X300/less deck, X300/38X, X300/42M, X300/42X, X300/48X, X300R, X304, and X324 Tractors.
NOTE: The rim diameter is larger for four-wheel steer tires, but does not affect chain requirements.
TY25229 tire chains - 20x10-8 (for some models), 22x9.5-12
NOTE: For LA165, LA175, D130, D140, D150, D155, D160, D170, E130, E140, E150, E160, E170, and E180 Tractors.
TY24327 tire chains - 22x11-10
NOTE: For X320, X340, and X360 Tractors.
TY15956 tire chains - 23x10.5-12
NOTE: For 190C Tractor.
TY26227 tire chains - 23x9.5-12, 24x9.5-12
NOTE: For X534 Tractor.
TY24328 tire chains - 24x12-12
NOTE: For X500, X520, X530, X540, and X590 Tractors. Also use with 26x10.5-12 tires on model year 2016- (SN 040,000-) X734 and X754.
TY25326 tire chains - 26x10.5-12
NOTE: For model year -2015 (SN -040,000). For X724, X734, X744, and X754 Tractors. Fits turf, bar, and heavy-duty all-purpose (HDAP) tire treads.
TY15958 tire chains - 26x12-12
NOTE: For X700, X710, X720, X730, X728, X738, X729, X739, X740, X750, X748, X758, and X749 Tractors. Will fit turf, bar, and HDAP tire treads. X729, X739, and X749 require BM22725 wheel spacer kit to provide clearance when installing tire chains.
The 42-in. (107-cm) Lawn Sweeper offers great performance and hauls an incredible 17 bu (599 L) of material. Its design gives superior brush-to-ground contact to prevent skipping and provide maximum performance for a clean path the first time through.
Features include:
John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.
This implement features legendary John Deere performance and quality.
Specifications
Brush height | Sweeping conditions |
Ground level to 1 in. (25 mm) above | Smooth surfaces - driveways, parking lots, and sidewalks |
1 in. (25 mm) to 2 in. (50 mm) | Mowed lawns under normal conditions, or light leaves |
2 in. (50 mm) to 3 in. (75 mm) | High grass, heavy leaves, or heavy grass clippings |
Customers, please contact your local John Deere dealer for availability and pricing information.
42-in. (107-cm) Tow-Behind Lawn Sweeper
Order number: LPSTS42JD
The 44-in. (112-cm) Lawn Sweeper offers great performance and hauls an incredible 17 bu (599 L) of material. Its design gives superior brush-to-ground contact to prevent skipping and provide maximum performance for a clean path the first time through.
Features include:
John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.
This implement features legendary John Deere performance and quality.
Specifications
Brush height | Sweeping conditions |
Ground level to 1 in. (25 mm) above | Smooth surfaces - driveways, parking lots, and sidewalks |
1 in. (25 mm) to 2 in. (50 mm) | Mowed lawns under normal conditions, or light leaves |
2 in. (50 mm) to 3 in. (75 mm) | High grass, heavy leaves, or heavy grass clippings |
Please contact your local John Deere dealer for availability and pricing information.
44-in. (112-cm) Tow-Behind Lawn Sweeper
Order number: LP49038
This John Deere dethatcher kit has two rows of individually flexing tines that gently but effectively remove grass clippings, leaves, and other lawn debris from your lawn. The kit easily attaches to the front of John Deere's 42-in. (107-cm) Lawn Sweeper (LPSTS42JD) to add thatch pickup to the sweeper's cleaning abilities. The dethatcher does not need to be removed to resume regular sweeping use.
Customers, please contact your local John Deere dealer for availability and pricing information.
Dethatcher kit for sweeper
Order number: LP42108
The Multi Tool includes one platform and two separate attachments, saving space and money.
John Deere has combined the best lawn tools into one package.
Two-year warranty.
Please contact your local John Deere dealer for availability and pricing information.
Multi Tool
Order number: LP39089
The Lawn Roller packs down sod, seed, and mole ridges. Its tough polyethylene drum does not dent or rust. The drum's rounded ends do not gouge the lawn or make ruts:
Nylatron is a trademark of QUADRANT AG or its affiliates or licensors.
John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.
This implement features legendary John Deere performance and quality.
Specifications
Width | 36 in. (91 cm) |
Roller | |
Size | 36 in. x 18 in. (91 cm x 46 cm) |
Capacity | 42 U.S. gal. (159 L) |
Weight (filled) | 390 lb (176.4 kg) |
Drum/end-cap material | High-density polyethylene (HDPE) |
Bearings | Nylatron |
Requirements and/or recommendations: tow-behind equipment
Customers, please contact your local John Deere dealer for availability and pricing information.
36-in. (91-cm) Tow-Behind Lawn Roller
Order number: LPPRT36JD
Compatibility and requirements and/or recommendations
Please contact a local John Deere dealer for availability and pricing information.
Steel roller 24 in. x 48 in. (61 cm x 122 cm)
Order number: LP64738
The 40-in. (102-cm) Plug Aerator removes plugs of soil up to 3-in. (7.6-cm) deep to allow penetration of air, water, and nutrients. It also helps relieve soil compaction:
John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.
This implement features legendary John Deere performance and quality.
Specifications
Width | 40 in. (101.6 cm) |
Aerator depth | Up to 3 in. (7.6 cm) |
Tines | |
Number of tips | 28 |
Spacing | 6 in. (15.2 cm) apart |
Material | Carbonized, 16-gauge, 0.6-in. (1.5-mm) steel |
Lift adjuster | Manual, three position |
Wheels | 4.10/3.5-4, pneumatic |
Weight-tray capacity | 175 lb (79.4 kg) |
Requirements and/or recommendations: tow-behind equipment
Customers, please contact your local John Deere dealer for availability and pricing information.
40-in. (102-cm) Tow-Behind Plug Aerator
Order number: LPPA40JD
The 48-in. (122-cm) Plug Aerator removes plugs of soil up to 3 in. (7.6 cm) deep to allow penetration of air, water, and nutrients and relieve soil compaction:
NOTE: The 48-in. (122-cm) Plug Aerator is not recommended for lawn tractors.
Nyliner is a trademark of Thomson Industries Incorporated.
John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.
This implement features legendary John Deere performance and quality.
Specifications
Width | 48 in. (121.9 cm) |
Aerator depth | Up to 3 in. (7.6 cm) |
Tines | |
Number of tips | 48 |
Spacing | 4 in. (10.2 cm) apart |
Material | Carbonized, 16-gauge, 0.06-in. (1.7-mm) steel |
Lift Adjuster | Manual, three positions |
Wheels | 4.10/3.5-4, pneumatic |
Weight-tray capacity | 250 lb (113.4 kg) * |
Requirements and/or recommendations: tow-behind equipment
Customers, please contact your local John Deere dealer for availability and pricing information.
48-in. (122-cm) Tow-Behind Plug Aerator
Order number: LPPA48JD
The 40-in. (102-cm) Spiker Aerator penetrates soil, allowing air, water, and nutrients to enter the lawn. It also relieves soil compaction:
John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.
This implement features legendary John Deere performance and quality.
Specifications
Width | 40 in. (101.6 cm) |
Aerator depth | Up to 2 in. (5.1 cm) |
Tines | |
Number of tips | 132 |
Diameter | 10 in. (25.4 cm) |
Spacing | 3.5 in. (8.9 cm) apart |
Material | Steel |
Lift adjuster | Manual |
Wheels | 4.10/3.5-4, pneumatic |
Weight tray capacity | 100 lb (45 kg) |
Requirements and/or recommendations: tow-behind equipment
Customers, please contact your local John Deere dealer for availability and pricing information.
40-in. (102-cm) Tow-Behind Spiker Aerator
Order number: LPSAT40JD
The roomy steel-frame cab shields the operator against snow, rain, sun, and wind.
Key features include:
Please contact your local John Deere dealer for availability and pricing information.
Weather enclosure
One 30-lb (13.6-kg) cast-iron weight may be installed on each front wheel for additional stability when operating on hillsides or with heavy rear equipment.
Requirements:
NOTE: Front wheel weights are not available for special-edition tractors because the styled front wheel design does not have appropriate holes for mounting the wheel weights and no adapter is available.
One or two 50-lb (22.7-kg) cast-iron weights may be installed on each rear wheel to provide extra traction and stability.
Features include:
NOTES:
For 50-lb (22.7-kg) cast-iron wheel weights on 23x10.50-12 or 24x12-12 rear tires:
BM17985 - for mounting one 50-lb (22.7-kg) weight
BM17977 - for mounting two 50-lb (22.7-kg) weights
For 50-lb (22.7-kg) cast-iron wheel weights on 26x12-in. rear tires:
BM17977 - for mounting one 50-lb (22.7-kg) weight
BM18101 - for mounting two 50-lb (22.7-kg) weights
For 70-lb (32-kg) starter cast-iron wheel weight on 26x12-12-in. rear tires:
BM18089 - for mounting 70-lb (32-kg) starter weight
For 70-lb (32-kg) starter and 50-lb (22.7-kg) cast-iron weight(s):
BM17977 - for mounting one 70-lb (32-kg) starter and one 50-lb (22.7-kg) weight
BM18101 - for mounting one 70-lb (32-kg) starter and two 50-lb (22.7-kg) weights
A - one (1) UC13499 and one (1) BM17972 weight
B - one (1) UC13499 and two (2) BM17972 weights
NOTE: Plastic wheel weight is not compatible with four-wheel-steer tractors.
For 50-lb (22.7-kg) cast-iron wheel weight on 26x10.50-12 tires:
BM18094 - for mounting one 50-lb (22.7-kg) weight
BM17977 - for mounting two 50-lb (22.7-kg) weights
NOTES:
For 50-lb (22.7-kg) cast-iron wheel weights on 23x10.50-12 or 24x12-12 rear tires:
BM17985 - for mounting one 50-lb (22.7-kg) weight
BM17977 - for mounting two 50-lb (22.7-kg) weights
For 50-lb (22.7-kg) cast-iron wheel weights on 26x12-in. rear tires:
BM17977 - for mounting one 50-lb (22.7-kg) weight
BM18101 - for mounting two 50-lb (22.7-kg) weights
For 70-lb (32-kg) starter cast-iron wheel weight on 26x12-12-in. rear tires:
BM18089 - for mounting 70-lb (32-kg) starter weight
For 70-lb (32-kg) starter and 50-lb (22.7-kg) cast-iron weight(s):
BM17977 - for mounting one 70-lb (32-kg) starter and one 50-lb (22.7-kg) weight
BM18101 - for mounting one 70-lb (32-kg) starter and two 50-lb (22.7-kg) weights
A - one (1) UC13499 and one (1) BM17972 weight
B - one (1) UC13499 and two (2) BM17972 weights
NOTE: Plastic wheel weight is not compatible with four-wheel-steer tractors.
For 50-lb (22.7-kg) cast-iron wheel weight on 26x10.50-12 tires:
BM18094 - for mounting one 50-lb (22.7-kg) weight
BM17977 - for mounting two 50-lb (22.7-kg) weights
The 42-lb (19-kg) Quik-Tatch can be used to counterbalance a heavy front or rear attachment and/or provide greater stability, especially when operating on hills.
This weight is constructed of cast iron and weighs approximately 42 lb (19 kg).
Some vehicles have built-in front and/or rear weight brackets to hang the weights on; others require a weight bracket that must be ordered separately.
X400/X500 Heavy-Duty Garden Tractors and X700 Series Tractors require the following parts when weights are installed on the front of the tractor:
Rear weight bracket is designed to hold two suitcase weights on X300 Tractors and up to four suitcase weights on X500 Multi-Terrain Tractors.
Hardware is required for installing each front-wheel weight.
Requirements:
NOTE: Front-wheel weights are not available for special edition tractors because the styled front-wheel design does not have appropriate holes for mounting the wheel weights and no adapter is available.